Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

BOYS AND THEIR TOYS
#1

Well, I know young boys like to play with their toys(like blocks)--but do men? Sometimes yes, sometimes no. For example my radio restorer seems very hesitant to "play" with the blocks on my Philco 38-690 even after I told him people on the Phorum say they are often bad. He's got my radio playing pretty well from what I can hear over SKYPE but is that good enough? He told me: "IN YOUR RADIO ARE 3 BLACK BLOKS : 32-2752 , 6287 SU, 3793DG". I would appreciate opinions from my learned members before this radio gets shipped to me! Thanks much and hope all have a Happy Easter or Passover.
#2

Sam

There is one block in the upper chassis of the 38-690 that absolutely should NOT be touched! It is part (97), and does not contain any capacitors, but instead a coil which is the set's 10 kc audio filter. Unpot that, and you may destroy that coil. That block is part no. 32-2752.

The other two are conventional bakelite block caps, and should be unpotted and the inside replaced with new caps.

--
Ron Ramirez
Ferdinand IN
#3

Those bakelite cap blocks will test your patience, but if I can do them, anyone can. Just takes time.

Here are the 2 links you need to know about:

http://www.philcoradio.com/tech/blocks.htm
http://www.philcorepairbench.com/capbuild.htm
#4

The bakelite block in my 40-190 was the very first thing I did in the re-build. Heck, haven't gotten much farther than that because nice weather's been taking me outside. Bakelite blocks are not complicated critters, but they do require patience.

And a nice handy guide like the two listed above, plus:

http://www.philcorepairbench.com/bblokcap.htm

Which is essentially the same info but with larger pictures. ;)




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently 3907 online users. [Complete List]
» 1 Member(s) | 3906 Guest(s)
Avatar

>