Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

PHILCO 296 Model H Speaker Question
#1

Please forgive my ignorance in advance. I have picked up a Philco 296 which I am in the earliest stages of learning to restore. The first and most obvious problem is the speaker is trashed. The paper is gone and the center voice coil is trashed. The speaker is a Model H, but can it be replaced with another Model? I have learned that the Model H is a 3200 Ohm speak operating at 40ma.(I think...) Is there another Philco speaker that I can replace this one. I see a Model G on EBAY with the same plug, but I am not sure if this would work. I have much to learn. Any suggestions? Thank you for any help.

Frank
#2

Hi Frank and welcome,
Have a look here   http://philcoradio.com/phorum/showthread.php?tid=215  Find spk zip and click on it. There you will find specs for all of the Philco speakers. Looks like there are 4 or 5 that use the same cone/voice coil assembly including the G and H models.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Welcome to the Phorum!
Icon_wave
#4

Thank you so much! I will go ahead and order the Model G and see where I am at. This will at least get me going. It may need to be re-coned and cleaned up, but perhaps this will at least get some sound.  The chassis is dirty but it looks like it has been recapped a long time ago and serviced several times over the years based upon on the dates and signatures. I have power to all the tubes so one step at a time. Thank you again and I may be back with several more questions.  Icon_wtf
#5

Thank you for having me. I am glad that I found this forum. I not afraid to learn, but I will admit that I am walking in the woods blind at this point. lol
#6

Have patience and you will be rewarded Icon_smile

Welcome.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#7

Terry and Mike will get you through it, have no fear. If you're an ace at reading schematics you're better off than I was a few months ago.

Greg

"We are here to laugh at the odds and live our lives so well that Death will tremble to take us."




Users browsing this thread:
[-]
Recent Posts
philco predicta
I found that where I have the 140v B+ there is 50v and the tuner receives 235v through the orange cablecgl18 — 04:14 PM
Philco 91 code 221
Chassis grounds thru rivets is another good place to look. Oh and the stator screws on the tuning cap where the leads at...Radioroslyn — 08:11 AM
Philco 91 code 221
Dirty tube pins and socket, cold solder joint, stray tiny strand of wire, clean the entire area around the oscillator tu...RodB — 08:43 PM
Philco 91 code 221
I have been restoring one of these sets and switched it on yesterday. It didn't exactly spring into life, but after a co...Philconut — 08:26 PM
Philco 50-925 antenna connections
That's super. Glad to hear you figured it out. Paul.Paul Philco322 — 11:11 AM
Philco 50-925 antenna connections
Hello Keith, great news !! Sincerely Richardradiorich — 02:14 AM
Philco 50-925 antenna connections
Finally, got the antenna fixed (repaired some broken wires) and have the radio playing. I've got four different schemat...keith49vj3 — 09:38 PM
1949 Motorola 5A9M
Bob, Nice radio.  I’ve not seen one before.  Keep us updated!Joe Rossi — 07:56 PM
Phioco 90 Power Transformer Wire Colors
Thanks for adding that information.klondike98 — 06:09 PM
Phioco 90 Power Transformer Wire Colors
Although I have used this site as a resource for a number of years this is my first post.   I am restoring a Model 90 si...vincer — 05:02 PM

[-]
Who's Online
There are currently 1457 online users. [Complete List]
» 1 Member(s) | 1456 Guest(s)
Avatar

>