Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x


Philco Model 70A "Lowboy"
#1

Hello,

I am new to the forum and I am hoping to get some help with a family heirloom.

I was recently preparing for a move when a metal beam fell on my dad's Philco that he inherited from his mom and dad. It cracked part of the front grill (photos attached). I was able to find two pieces that clicked back together but was unable to find the other pieces. I assume that either due to age or impact, they were pulverized. 

He left it to me when he passed as a repair and restoration project (a majority of parts were missing) when i was older as we enjoyed fiddling with Pioneer, Sansui, and Kenwood stereos. 

Is this possible to fix in any way? I have had trouble finding information about the model or the type of wood (to try and do an epoxy fix).

Also, if you know of any body able to help or do restorations it would be greatly appreciated. 

Thank you.


Attached Files Image(s)
                   
#2

I would just use a wood glue, and some sort of clamps, binder clips will probably suffice, to put the large pieces back. To me it looks like there enough pieces there to perform a near invisible repair, at least with the walnut veneer that goes on top, save gluing the walnut veneer on for last. If there are small chips out of whatever is underneath some filler should do the job, you can shave off the excess with something like a scalpel or x-acto knife, and sandpaper. The part you show with the dent, that can be fixed with carful use of a damp rag, or paper towel, and a clothes iron, a soldering iron will also work, placed right over the dented area. When your cabinet had a finish on it, a lot of the damaged areas would have been covered by paint or shaded lacquer, so al long as the pieces are glued in straight, and smooth, they will be nearly invisible once a finish goes back on.
Regards
Arran
#3

Hi VintageGuy95, welcome to the Phorum.

Nice label on that chassis.

If you're looking for electronic restoration you might try Jim Lindenas, jlindenas@gmail.com. He's in Orillia and does YouTube videos about repairing tube radios. Nice day trip to the lake country.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 71 Code 125
Ok guys. Thanks for the input. As for AI this is why I ask the experts. Dandconant — 07:39 AM
Philco 71 Code 125
Technically, that's C-. B- is chassis ground. The resistor between chassis ground and the HV center tap makes the HV c...MrFixr55 — 11:24 PM
54C Cabinet Refinish
hello Roy, I’d follow Arran’s suggestion and use automotive gasket material, which I keep around for situations like th...radiorich — 10:22 PM
Philco 71 Code 125
This might be one of those cases where it's a ground to an AC voltage and B- to DC.RodB — 08:22 PM
Philco 71 Code 125
Really Rod? I know you would not steer me wrong but AI say this is a short circuit? What if I moved the 6 volt center ta...dconant — 06:40 PM
54C Cabinet Refinish
Roy; Personally I would have left the asbestos alone if it were my set, but you can find a modern substitute that som...Arran — 04:51 PM
Philco 71 Code 125
Looks like that might be the B- buss, so that would be correct.RodB — 01:32 PM
Philco 71 Code 125
I noticed on the code 121 schematic the center tap for the 6 volt winding and hv winding are tied together. Is this corr...dconant — 12:16 PM
Philco 45-6365 Universal IFT Instruction Manual
The Philco Parts Catalog for 1942 shows it as usable for 175 kHz, 260 kHz, and 465 kHz. The instructions will show how t...DaleHCook — 11:19 AM
Stromberg Carlson 1500 Squeal
Hello Rob, I agree with you—I have one here at my house that I need to check out. It’s way over-engineered just to make...radiorich — 11:05 AM

[-]
Who's Online
There are currently no members online.

>