Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

42-1008P Stain *Cabinet Done*
#31

So here is what I am wondering about.


[Image: http://i1289.photobucket.com/albums/b519...edp7bu.jpg]

I believe the unit had original finish on it so from what I can see the trim piece that comes up along side the door is dark like other dark areas (red oval) and then hits a transition or swirl into that flat side piece (orange circle) and then the flat side (blue circle) is just about as toned as the face.

Does that seem to be what I should be going after?
#32

Just when you think you have a section looking good the sun hits it just right and you see a bad sanding job Icon_sad

Going to move on and figure out if I want to worry about fixing it.

I'm not all that good at this wood stuff.
#33

(03-28-2015, 01:16 PM)Edisla Wrote:  Just when you think you have a section looking good the sun hits it just right and you see a bad sanding job Icon_sad

Going to move on and figure out if I want to worry about fixing it.

I'm not all that good at this wood stuf
Edisla, don't give up. You have been working hard on it. Maybe just sand a little more with finer sand paper and it will look nice when covered with clear, etc. Icon_smile Don't forget to always sand WITH the grain.
#34

I wont give up.

I may give in a little but will not give up.
#35

Well here is how it came out.

Not exactly how I wanted it but it is close enough.

Before

[Image: http://i1289.photobucket.com/albums/b519...vxg1z2.jpg]

After
[Image: http://i1289.photobucket.com/albums/b519...cvak9q.jpg]
#36

Lookin Nice ...
#37

Yes it does look nice... Icon_thumbup Icon_thumbup
#38

looks fine to me great job Icon_clap Icon_thumbup
sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently no members online.

>