Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

42-1008P Stain *Cabinet Done*
#31

So here is what I am wondering about.


[Image: http://i1289.photobucket.com/albums/b519...edp7bu.jpg]

I believe the unit had original finish on it so from what I can see the trim piece that comes up along side the door is dark like other dark areas (red oval) and then hits a transition or swirl into that flat side piece (orange circle) and then the flat side (blue circle) is just about as toned as the face.

Does that seem to be what I should be going after?
#32

Just when you think you have a section looking good the sun hits it just right and you see a bad sanding job Icon_sad

Going to move on and figure out if I want to worry about fixing it.

I'm not all that good at this wood stuff.
#33

(03-28-2015, 12:16 PM)Edisla Wrote:  Just when you think you have a section looking good the sun hits it just right and you see a bad sanding job Icon_sad

Going to move on and figure out if I want to worry about fixing it.

I'm not all that good at this wood stuf
Edisla, don't give up. You have been working hard on it. Maybe just sand a little more with finer sand paper and it will look nice when covered with clear, etc. Icon_smile Don't forget to always sand WITH the grain.
#34

I wont give up.

I may give in a little but will not give up.
#35

Well here is how it came out.

Not exactly how I wanted it but it is close enough.

Before

[Image: http://i1289.photobucket.com/albums/b519...vxg1z2.jpg]

After
[Image: http://i1289.photobucket.com/albums/b519...cvak9q.jpg]
#36

Lookin Nice ...
#37

Yes it does look nice... Icon_thumbup Icon_thumbup
#38

looks fine to me great job Icon_clap Icon_thumbup
sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 2940 online users. [Complete List]
» 3 Member(s) | 2937 Guest(s)
AvatarAvatarAvatar

>