Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Which Mohawk toner - Tone Finish or Ultra Classic?
#1

I was hoping you would know how to tell which Mohawk toning spray colors are opaque and which are transparent. I am talking about the spray cans of toner.

Chris

!!!!!!!!!!!!!!!!!!!RESISTANCE IS FUTILE!!!!!!!!!!!!!!!!!!!!!!  
                           /\/\/\/\/\/\/\/\/\
                                                     
                                 [Image: http://philcoradio.com/phorum/images/smi...on_eek.gif]  Chris
#2

Chris

If you are using spray cans...

Tone Finish is opaque, Ultra Flo is transparent. I used to use Tone Finish, but I started transitioning to Ultra Flo a couple years ago. It's a slow transition for me as I bought several cans of Medium Walnut Tone Finish - which, fortunately, is closer to being transparent than other Mohawk colors.

--
Ron Ramirez
Ferdinand IN
#3

Ron
You mean the Mohawk Ultra Classic Toner line? What are favorite shades of toner to use?

!!!!!!!!!!!!!!!!!!!RESISTANCE IS FUTILE!!!!!!!!!!!!!!!!!!!!!!  
                           /\/\/\/\/\/\/\/\/\
                                                     
                                 [Image: http://philcoradio.com/phorum/images/smi...on_eek.gif]  Chris
#4

Yeah, I meant Ultra Classic, not Ultra Flo. Years ago Mohawk had an "Ultra Flo" line and for some strange reason, the name has stuck in my head. Icon_crazy

I have yet to try Medium Brown Walnut but I am assuming that is the Ultra Classic version of Medium Walnut. I've used Perfect Brown (a bit darker than Medium Walnut) and Extra Dark Walnut, and have been pleased with both. I now prefer Extra Dark Walnut Ultra Classic to Extra Dark Walnut Tone Finish for the areas needing to be super dark, almost black but not quite.

--
Ron Ramirez
Ferdinand IN
#5

Ron
OK
I have been trying to finish two radio cabinets and I ran out of some colors.
Made an order for Mohawk and ended up with opaque toners. Of course I wanted transparent toners Hense the post about toners.

Yes Ive been using some earlier cans of perfect brown that are transparent and not being able to match up different areas of wood.

Perfect brown is a little too red for this Crosley.

Radios:  Philco 45 and   Crosley 645   6volt unit. I think.

So if medium brown walnut is lighter than perfect brown I will skip the medium brown.
I am looking for one a little darker than perfect brown? same tone.
And one that is not quite so red as perfect brown.
All transparent.

Oh and I am trying out their Heavy bodied sanding sealer to try it as  grain filler.

Hope Fred doesn't mind butting in on his post. Maybe I should start one of my own.

Thanks
Chris

!!!!!!!!!!!!!!!!!!!RESISTANCE IS FUTILE!!!!!!!!!!!!!!!!!!!!!!  
                           /\/\/\/\/\/\/\/\/\
                                                     
                                 [Image: http://philcoradio.com/phorum/images/smi...on_eek.gif]  Chris
#6

I split this into its own thread.

Icon_smile

As I recall there is a "Medium Dark Walnut" but I have yet to try it. It might be good for the triple-toned Philco cathedrals such as the flat-face 44B if Perfect Brown isn't dark enough. You know, something like Medium Brown Walnut, Medium Dark Walnut, Extra Dark Walnut.

--
Ron Ramirez
Ferdinand IN
#7

Thanks Ron for the info. I will try and post some pics when I finally get the colors right.
Chris

!!!!!!!!!!!!!!!!!!!RESISTANCE IS FUTILE!!!!!!!!!!!!!!!!!!!!!!  
                           /\/\/\/\/\/\/\/\/\
                                                     
                                 [Image: http://philcoradio.com/phorum/images/smi...on_eek.gif]  Chris
#8

Hey Chris
I had the same issue w/ the Mohawk walnut toners. I found them to be very red, was somewhat disappointed w/the results.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#9

Most people put on too much. Start lightly and never spray directly at the surface.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#10

Yes it's a steep learning curve.

!!!!!!!!!!!!!!!!!!!RESISTANCE IS FUTILE!!!!!!!!!!!!!!!!!!!!!!  
                           /\/\/\/\/\/\/\/\/\
                                                     
                                 [Image: http://philcoradio.com/phorum/images/smi...on_eek.gif]  Chris
#11

Hey Phlogiston-

I'm trying to soak in as many finishing tips as I can from this forum, but I'm a little confused by your "never spray directly at the surface" tip. Did you mean to say: spray at a low angle to the surface as opposed to 90 degrees (perpendicular) to the surface? Or am I incorrectly interpreting your comment.
#12

You are correct. Let the spray hit the surface at an angle and distance that the spray is more or less dropping onto the surface.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#13

Got it! That's a great tip. I never would have thought to try that.




Users browsing this thread:
[-]
Recent Posts
Model 80 Antenna Issue?
Thanks Gary and Rod.  I also found an article in the Philco Repair Bench under Service Hints and Tips, about installi...Hamilton — 12:32 PM
Model 80 Antenna Issue?
Hello Hamilton, here is a little information found in our Philco Radio Library at the bottom of the Home page. Hope it ...GarySP — 11:28 AM
Model 80 Antenna Issue?
I did as you suggested and touching the middle of the volume control did nothing so the coil has to be rewound. Any idea...Hamilton — 10:19 AM
1949 Motorola 5A9M
This would be the second portable in the "other radios" forum where I have a similar one in my collection. I h...Arran — 12:41 AM
Looking for any info: 1977 Ford-Philco Console Hi-Fi Turntable and Radio
Hi PittsburgTost. The record changer looks like a Garrard or BSR (Likely Garrard). The spindles just pull out and pu...MrFixr55 — 11:57 PM
Looking for any info: 1977 Ford-Philco Console Hi-Fi Turntable and Radio
Hello PittsburghToast , Welcome aboard and it looks like gary may have something for you ! now if I dig through my se...radiorich — 11:35 PM
Model 80 Antenna Issue?
You are kind of on the right path. You can touch the grid cap of the Detector/Oscillator 36 tube. I'm expecting a respon...RodB — 08:48 PM
Looking for any info: 1977 Ford-Philco Console Hi-Fi Turntable and Radio
Welcome to the Phorum, PittsburghToast!  I found an old thread that my interest you regarding the quality and worth of P...GarySP — 08:48 PM
Looking for any info: 1977 Ford-Philco Console Hi-Fi Turntable and Radio
Welcome to the Phorum! :wave: We do not have anything on that unit in our digital library. There is a Sam's Photof...klondike98 — 08:47 PM
Model 80 Antenna Issue?
I’ve replaced all the caps and resistors and the radio is working but minimal volume unless I put my hand near the re...Hamilton — 08:24 PM

[-]
Who's Online
There are currently no members online.

>