Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Padded Feet for Philco 38-15
#1

Ron,

1. I have a Philco 38-15 that has four padded feet. They look like a thumb tack and are just slightly bigger. On the underside is inscribed MATTATUCK WATERBURRY. Do you know if replacements are available?

2. I also need a back for a Philco 40-124. And the correct grill cloth pattern.

Thank you.

David G. Woodward
#2

WildDog Wrote:1. I have a Philco 38-15 that has four padded feet. They look like a thumb tack and are just slightly bigger. On the underside is inscribed MATTATUCK WATERBURRY. Do you know if replacements are available?

If these are the same feet as Philco used on their cathedrals and tombstones (and I suspect they are), these are no longer being manufactured (as far as I know). Many cabinet refinishers, such as Barry Jones, use small circular stick-on felt pads instead which do a better job of protecting the furniture they sit on top of.

Quote:2. I also need a back for a Philco 40-124. And the correct grill cloth pattern.

Sorry, can't help you on the back. I suggest you put an ad in the Philco Wanted section.

As for the cloth, that particular pattern is not being reproduced. A similar pattern is #8 from Radio Grille Cloth Headquarters.
http://www.grillecloth.com/

The 40-124 in my site's Gallery does not have the correct cloth for this reason. The correct pattern may be seen on the 40-90CB:
http://www.philcoradio.com/gallery/1940a.htm#e

--
Ron Ramirez
Ferdinand IN
#3

This type of glide is available. A little bulky, though.

http://www.floorsaverglide.com/catalog/i...p?cPath=27

http://www.allglides.com/feltpads.html

[Image: http://www.floorsaverglide.com/catalog/i...nailon.jpg]

I use a nail-on plastic type from McMaster-Carr.

[Image: http://www.mcmaster.com/catalog/116/gfx/...13tp2s.gif]
#4

Thank you all for your help.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5588 online users. [Complete List]
» 1 Member(s) | 5587 Guest(s)
Avatar

>