Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Phonograph with Philco by Radiobar
#16

Since I sorta got this thread off-topic for a bit, I'm going to start a new thread dedicated only to the Phonograph with Philco by Radiobar.

Pat
#17

Here are some pics of the unit sent to me by the PO. He just delivered the unit to me yesterday, so I haven't had a chance to go through it yet. Someone out there MUST have more information on this. All I can find is what Ron has, including the Mulholland Press info. 

Cabinet made and marketed by Radiobar, a Philco 38-3 chassis, and a Capehart automatic record changer.
[Image: http://i1367.photobucket.com/albums/r796...6mu61p.jpg]
[Image: http://i1367.photobucket.com/albums/r796...3atcur.jpg]
[Image: http://i1367.photobucket.com/albums/r796...yhieir.jpg]
[Image: http://i1367.photobucket.com/albums/r796...ptvf1d.jpg]
#18

WOW  that looks great Icon_thumbup
looks pretty good condition too.  maybe just touch up ?
you could always send out to east coast if you don`t have room for it Icon_mrgreen
sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#19

(07-25-2015, 12:30 PM)sam Wrote:  WOW  that looks great Icon_thumbup
looks pretty good condition too.  maybe just touch up ?
you could always send out to east coast if you don`t have room for it Icon_mrgreen
sam

Yeah Sam, I think you're right. Maybe just touch up. Except for the lid. The inside of the lid is pristine, including the felt, but the top HAS to be refinished.

And I DON'T have room for it, so it will be on ebay when I'm done. 'Course shipping wouldn't be too cheap. It measures 42x37x19, and has to weigh more than 100 lbs.

Pat 
#20

Nice restorations! I merged your two threads as they are primarily both about the same set.
#21

(07-25-2015, 04:12 PM)klondike98 Wrote:  Nice restorations!  I merged your two threads as they are primarily both about the same set.

O.K. Thanks

Pat




Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM

[-]
Who's Online
There are currently no members online.

>