Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Escutcheon screw question
#1

Am trying to source some escutcheon screws for my 41-300. Pretty sure that Philco used the same small screws on most of there escutcheons thru the 30's and early 40's. Older ones where painted black.
Anyway I don't have an accurate way to measure the diameter. My best guess is a number 3 but not sure. Anyone know what it is??

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#2

As luck would have it I was digging around for some 6pin tube socket for someone and found a small bag the wood screws suitable for this application. They are #2 x 3/8" long, brass round slotted head. Hillman pn 49114. Good match for the originals except that the bottom of the head isn't tapered it's flat.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

I always knew you had a few screws missing  Icon_thumbup

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#4

(08-10-2017, 07:47 PM)Radioroslyn Wrote:  .... the bottom of the head isn't tapered it's flat.

No one will know.

And we won't tell.
And we will even ask Sam to delete this thread.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#5

(08-10-2017, 08:28 PM)morzh Wrote:  
(08-10-2017, 07:47 PM)Radioroslyn Wrote:  .... the bottom of the head isn't tapered it's flat.

No one will know.

And we won't tell.
And we will even ask Sam to delete this thread.

Icon_lol

What kind of horrible person would give you a radio without escutcheon screws! Shame! Icon_lol

Icon_smile

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
And so does a barber shop quartet. mmmmmmRodB — 03:54 PM
Shadow Meter Bulb
I did try an LED bulb in place of the original but wasn't impressed with the amount of light on the dial. Seems like it ...RodB — 03:51 PM
HiFi (Chifi) tube amp build - but my own design.
Tim Would mounting he transformer vertically change the hum, if used without additional parts? Also, in these amps...morzh — 02:25 PM
Shadow Meter Bulb
Gary I doubt it would introduce any noise. We use similar lamps for the panel indication, 12V AC lamps: they are LEDs...morzh — 02:15 PM
Shadow Meter Bulb
Not sure if anyone has tried this but there are 6.3 volt miniature lamps in bayonet and screw-in base options available ...GarySP — 11:31 AM
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM

[-]
Who's Online
There are currently 5092 online users. [Complete List]
» 2 Member(s) | 5090 Guest(s)
AvatarAvatar

>