Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Escutcheon screw question
#1

Am trying to source some escutcheon screws for my 41-300. Pretty sure that Philco used the same small screws on most of there escutcheons thru the 30's and early 40's. Older ones where painted black.
Anyway I don't have an accurate way to measure the diameter. My best guess is a number 3 but not sure. Anyone know what it is??

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#2

As luck would have it I was digging around for some 6pin tube socket for someone and found a small bag the wood screws suitable for this application. They are #2 x 3/8" long, brass round slotted head. Hillman pn 49114. Good match for the originals except that the bottom of the head isn't tapered it's flat.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

I always knew you had a few screws missing  Icon_thumbup

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#4

(08-10-2017, 06:47 PM)Radioroslyn Wrote:  .... the bottom of the head isn't tapered it's flat.

No one will know.

And we won't tell.
And we will even ask Sam to delete this thread.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#5

(08-10-2017, 07:28 PM)morzh Wrote:  
(08-10-2017, 06:47 PM)Radioroslyn Wrote:  .... the bottom of the head isn't tapered it's flat.

No one will know.

And we won't tell.
And we will even ask Sam to delete this thread.

Icon_lol

What kind of horrible person would give you a radio without escutcheon screws! Shame! Icon_lol

Icon_smile

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently no members online.

>