Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 86
#31

Thanks Bob,
I have it almost done but not near as good as I had hoped. The inner fine pieces are really brittle and break with the slightest touch. I'll give the glue the rest of the day to dry and see what happens. That is a good idea since the veneer came in l large sheet.
George
#32

I have gone as far as I can with this. It isn't as nice as yall would have done but I am afraid if I keep trying to make it better I will end up making it worse. My thanks to all who helped me with this this restoration, electrical and cabinet. This phorum is loaded with experts that are more than willing to help. Once again thank you all.
George


Attached Files Image(s)
   
#33

It's fine. Good job saving that cabinet. Icon_smile

Now, do be careful moving it around. Do not scoot it! You don't want that leg to break again, or risk breaking another. I know how heavy those things are. Icon_eek

--
Ron Ramirez
Ferdinand IN
#34

Hello George,
Well Done and I bet that Set is Heavy I have a General Motors model 160b that weighs as much at a small car !

Sincerely Richard
#35

Thank you Ron and Rich,
Yes it is very heavy, I had my wife help me carry it to the living room where it will stay. No sliding allowed. Thinking about trying to restore my model 65, but have to go thru all the files and info because I don't have a speaker for it. You guys are great!
George
#36

Looks great. Well done !!
#37

George, I would be very happy with that cabinet refinish. The legs look very good. Take care and BE HEALTHY! Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan




Users browsing this thread:
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2844 online users. [Complete List]
» 3 Member(s) | 2841 Guest(s)
AvatarAvatarAvatar

>