Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 42-854T purchase
#1

I just purchased a Philco model 42-854t for $80 it takes awhile to warm up but plays very well the outer case is in great condition a couple scraps. was it a good deal ? I would like to tune it up how should I start. Any info would be helpful.

Thanks,
Steve
#2

Welcome to the Phorum!
Icon_wave
Here's a little info on your model from the Gallery.

A few questions to help gauge the next steps.
1) Do you know if the set has been recapped recently?  If not, that may be the first order of business.  

2) How familiar are you with electronics?  If you are new to this, here's a nice place to start reading: http://www.antiqueradio.org/begin.htm

3) Can you post a picture of the top and underside of the chassis?  That might help us figure out if its been recapped if you don't know.  How to post pics can be found here: http://www.philcoradio.com/phorum/showthread.php?tid=29

A free version of the schematic can be found at: http://www.nostalgiaair.org/pagesbymodel...013562.pdf
but if you need to do anything involving the schematic you may want to order a set from Chuck Schwark for a few bucks.  They will be much easier to read than the free version.  Go to: http://www.philcorepairbench.com/schematics.htm
#3

Hi Steve and welcome!
My condolences on getting the portable.
http://philcoradio.com/phorum/showthread.php?tid=14647

Just kidding (I think)

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

 If the set was electrically restored, (including the rubber/gutta perch wire replaced) and is in excellent cosmetic condition (plastic escutcheon and knobs not warped to death and cracked), maybe $80 on a very good day, otherwise no.
If you run into another radio that you are thinking about buying, not necessarily a Philco, ask the phorum before laying your money down.
Regards
Arran
#5

Very common  for these '41 and '42 sets to have a grill shrinkage. Sometimes the knobs too. Originals are light brown tenite I found some dark brown bakelite philco to replace you warped ones.


Attached Files Image(s)
           

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#6

terry
come on show off Icon_evil
wrong knobs Icon_e_surprised

reminds me KIRK  where`s are knobs
ps kirk has grills if yours is warped
sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#7

I am working on them Sam....
I haven't had much time.. Gotta make a new mold, the other wasn't letting the air out...

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM

[-]
Who's Online
There are currently 990 online users. [Complete List]
» 1 Member(s) | 989 Guest(s)
Avatar

>