Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco signal tracer model 7030
#1

I have picked up a 7030 in very good exterior condition, makes a nice display piece. I am wondering if restored it would have better performance than a common Heath or Eico unit.
Thanks
Hank
#2

I have one that I replaced the caps in and had to resolder the cable where it went into the probe. There is a tube in the probe.
I have not used it for troubleshooting yet but here is an instruction manual in case you don't have one.
http://www.myvintagetv.com/Apple%20PDF%2...Tester.pdf
Don't know if its better than Heath or Eico. Maybe someone can comment on that.
#3

(10-01-2016, 08:39 PM)KCMike Wrote:  I have one that I replaced the caps in and had to resolder the cable where it went into the probe. There is a tube in the probe.
I have not used it for troubleshooting yet but here is an instruction manual in case you don't have one.
http://www.myvintagetv.com/Apple%20PDF%2...Tester.pdf
Don't know if its better than Heath or Eico. Maybe someone can comment on that.

Thanks, I downloaded the manual, sounds interesting.  I think I will go throuth it, and try it out.  I did slide the the probe apart, some of the terminal clearances are very close and could use insulation.
Hank




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 1520 online users. [Complete List]
» 1 Member(s) | 1519 Guest(s)
Avatar

>