Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.
Working on a 38-116 code 125 and have a question concerning bakelite blk. number 46.
This is a 4989SG which is listed on the parts list as having a single .1 uf cap.
If you look on the handy reference guide that I printed out from the Philco site, it does not list a 4989SG.
Anyone know what the proper wiring would be as far as the new .1 cap.
Lugs 1 to 2 or lugs 1 to 3 ?
Thanks,
murf
Posts: 62
Threads: 20
Joined: Apr 2015
City: Decatur Alabama
According to Ray Bintliff's book "Philco condensers and more", the 4989SG block contains one .09 cap connected from lug 1 to 3.
Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.
Guess the parts list is wrong?
Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.
After looking farther, I see there is a 4989DG that is not listed as well.
Schematic view and the parts list only show 3 blocks instead of the 6 or 7 blks that are used in the chassis.
What's up ?
Murf
Posts: 62
Threads: 20
Joined: Apr 2015
City: Decatur Alabama
And according to "Condensers and more" the 4989 DG is two .09 condensers, first is lug 1 to 2, second is lug 1 to 3. Lug 1 goes to chassis ground.
Posts: 1,402
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO
Quote:Guess the parts list is wrong?
.09 or .1 same thing.
Steve
M R Radios C M Tubes
Posts: 62
Threads: 20
Joined: Apr 2015
City: Decatur Alabama
Oh yeah. Close enough for me.
Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.
OK, thanks for the info Doc.
I guess the others that are not shown on the schematics will have to be done using the number marked on the block.
Wish it were clearly marked on the schematics so there is no guess work involved.
Thanks again,
Murf
Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.
(04-10-2017, 08:54 PM)Steve Davis Wrote: .09 or .1 same thing.
Kinda figured that was the case.
Any idea why the rest of the blocks are not shown on the schematics ?
Don't want to guess on these, it is too much work to re-do these.
Thanks Steve,
Murf
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
I took a look at the schematic and saw only one #46 cap, screen bypass for the IF amp stage. The parts list sez it's a .1mfd (probably 400v) it doesn't say dual so I'm thinking it's a single unit. Have a look at the eyelet to see if the center terminal has a wire coming up thru it.
As mention .09 hasn't been a standard value for a million years.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.
Hi Terry,
Yes I can see the leads coming thru the rivets, but why don't they show all of the Bakelite blocks on the schematics?
Hate guess work.
Thanks,
Murf
Posts: 736
Threads: 26
Joined: Jun 2013
City: Hayward, California
As im sure you all knew... Doc is right on the two cap blocks info. Just wanted to put my 2 cents worth in. 
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Ok....
Does resistor #45 connect between the two ungrounded terminal of 46??
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.
(04-10-2017, 10:39 PM)Radioroslyn Wrote: Ok....
Does resistor #45 connect between the two ungrounded terminal of 46??
Yes there is.
Started recapping the blocks today.
So far so good. 3 down and 3 to go.
Murf
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Ok The other cap in that block is #9 a .05 (a 473 in these new fangled numbers). This is what the schematic shows, parts layout sez different. Having a extra .05mf isn't going to make any difference.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 04-11-2017, 07:56 PM by Radioroslyn.)
Users browsing this thread: 2 Guest(s)
|
|
Recent Posts
|
|
HiFi (Chifi) tube amp build - but my own design.
|
| Tim,
nice write up and thanks for sharing !!
Sincerely Richardradiorich — 02:47 AM |
|
HiFi (Chifi) tube amp build - but my own design.
|
| Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM |
|
Shadow Meter Bulb
|
| Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM |
|
Philco 41-608 changer coupler
|
| 3D-printing...short of machining, of course.
Or molding.morzh — 05:20 PM |
|
Philco 41-608 changer coupler
|
| Thanks, Morzh.
That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM |
|
12' Philco
|
| If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel.
Kareem would have an e...morzh — 01:48 PM |
|
12' Philco
|
| And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM |
|
Hickok AC51 tube tester
|
| I think they have only shown the secondaries of the transformer.
Two of them feed the rectifiers' filaments.morzh — 12:58 PM |
|
IF can wire size and Rubber mounts?
|
| Arran
If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM |
|
12' Philco
|
| Rod,
Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently.
H...morzh — 12:54 PM |
|
Who's Online
|
There are currently 6946 online users. [Complete List]
» 2 Member(s) | 6944 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
