1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
50-1724-121 power cord question
Project80Pete
Junior Member
**
Posts: 7
Threads: 3
Joined: Dec 2017
City: Lubbock, TX
#1

12-03-2017, 11:53 AM
Just bought my first phonograph/radio and am completely new at this.  The previous owner tried to power the unit with duct tape around the power cord as the insulation had deteriorated but of course got a pretty good spark.  I’m replacing the power cord now but noticed something a bit strange (at least for me) in the middle of the cord.  Can anyone tell me what this is for and how to get a proper replacement?


Attached Files Image(s)
   
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

12-03-2017, 05:52 PM
Hi and welcome,
Your cord should be just the run of the mill 2 conductor job BUT it has a third wire that is connect to the FM ant. It doesn't connect the either of the wires carrying the ac current, typically it should end near the plug. You don't have use the 3rd wire it was just a simple way to make a short not very effective FM ant. If you choose not to you'll need to wire up an ant for the FM band.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 12-03-2017, 06:46 PM by Radioroslyn.)
Find
Project80Pete
Junior Member
**
Posts: 7
Threads: 3
Joined: Dec 2017
City: Lubbock, TX
#3

12-03-2017, 06:13 PM
Thanks Terry, I appreciate all the help I can get.
Find
klondike98
Phorum Moderator
******
Posts: 5,084
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#4

12-03-2017, 07:23 PM
Welcome to the Phorum!
Icon_wave
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
Project80Pete
Junior Member
**
Posts: 7
Threads: 3
Joined: Dec 2017
City: Lubbock, TX
#5

12-03-2017, 07:35 PM
Thanks Bob
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 6131 online users. [Complete List]
» 2 Member(s) | 6129 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration