Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Need guidance in selecting a Lowboy
#16

I think that I would hold off for something a little closer then Pennsylvania, those 1929 Philcos in the lowboy cabinet seem to turn up everywhere at some point. The one Willy has has been messed with, I would sooner get one that still has a worn out original finish then a stain n' polyed blunder like that.
Regards
Arran
#17

Thx Arran, I was kinda leaning in that direction. Unfortunately, I'm far less a wood worker than in restoring electronics, but of course would rather have something that looks un-tampered with. If they messed with the cabinet, who knows what they might have done to the circuitry.

I've bought two consoles from Willy in the past. He could give a class on how to pack and ship, and his rate is fair, currently $90.
#18

I passed on Willeez offering, and have recently been in contact with the eBayer offering the one I had displayed earlier in the thread;

[Image: https://i.ebayimg.com/images/g/~5gAAOSwH...s-l500.jpg]

Since the seller is acting like he doesn't know jack about these, I asked him to send me scans of the back;

[Image: https://i.ebayimg.com/images/g/rBQAAOSwO...-l1600.jpg]

[Image: https://i.ebayimg.com/images/g/Aa8AAOSwW...-l1600.jpg]

[Image: https://i.ebayimg.com/images/g/jicAAOSwd...-l1600.jpg]

It appears to have original parts, but he told me that it only has 6 tubes, which seems to be apparent from the scans.

What model would this be, and would it be a decent performer AFA sensitivity and audio quality for a TRF?
#19

Looks to be a model 87 but is missing the two 45 output tubes. Performance is good and is a good sounding set for 1929 technology. Here's a good pic of an 87, the output tubes are up in the right front corner.


Attached Files Image(s)
   

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#20

Thanks! OK, so given the scans, what should I offer him for it, (plus of course shipping) ?
#21

I'd go $50-75. If you need some bargaining chips the missing 45's and if your close enough the see it in person check the spkr plug (all 4 pin should have some resistance to each other). If not then you may be looking at another $50 for a replacement. The cabinet looks a little dull not sure if it's been stripped or not. Color looks pretty good.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#22

He's had a BIN going since November; 8 consoles for $500, or $62.50 each, so that's what I offered him for it, after pointing out the need for two 45 tubes and posting an eBay link displaying one shoulder tube offered for $40, and another with two for $75.
I also explained about possibly needing another speaker plug if the pins on his don't show resistance to each other, at a cost of up to $50.

Stay tooned... ;)
#23

He got back to me and said that he was selling 8 consoles, not one. Good luck with that. I told him my offer stands unless/until I find another.

BTW, if anyone has one of these consoles they could part with, I'd be interested, obviously.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM

[-]
Who's Online
There are currently 1006 online users. [Complete List]
» 2 Member(s) | 1004 Guest(s)
AvatarAvatar

>