Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Emerson 517 Moderne
#1

Well I had got 3 free radios a while back, one went to Terry, one is still in the box, this Emerson got done! The lighted dial pic is does not do justice, the cabinet came out OK, used Meguiars Wax and it came up good. I took the cabinet from a junker as the original had a big hole in top. 

It has been to the bench and it sounds quite nice, picks up my 250 Watt AM music station very well. So now I am wondering if I should give this to the guy who gave it to me, It was his Dad's.


https://www.flickr.com/photos/92577012@N...2698130911

What does ya think?

Paul

Tubetalk1
#2

Looks great!
Darn I thought you fixed the old cabinet!
Hear your going to be snow in pretty soon.
Got to get busy on that GE cabinet. I found
some small brads so I can nail the top back down.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

By the time I fixed the hole It would have cost me way more than the junk set, I needed a knob and I took the case. I still have a chassis that is not too bad though it has the small tubes instead of the Octal like the one we fixed. 

Paul

Tubetalk1
#4

Nice!

What's that big white console The Emerson was sitting on for the pictures?  Icon_wink

I don't hold with furniture that talks.
#5

I would give it back, lots of memories of his dad. David
#6

(03-14-2018, 12:21 PM)EdHolland Wrote:  Nice!

What's that big white console The Emerson was sitting on for the pictures?  Icon_wink



That is my Whirlpool console sounds good especially if change was left in your pocket. Icon_lol

Paul

Tubetalk1




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently 5426 online users. [Complete List]
» 1 Member(s) | 5425 Guest(s)
Avatar

>