Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Emerson 517 Moderne
#1

Well I had got 3 free radios a while back, one went to Terry, one is still in the box, this Emerson got done! The lighted dial pic is does not do justice, the cabinet came out OK, used Meguiars Wax and it came up good. I took the cabinet from a junker as the original had a big hole in top. 

It has been to the bench and it sounds quite nice, picks up my 250 Watt AM music station very well. So now I am wondering if I should give this to the guy who gave it to me, It was his Dad's.


https://www.flickr.com/photos/92577012@N...2698130911

What does ya think?

Paul

Tubetalk1
#2

Looks great!
Darn I thought you fixed the old cabinet!
Hear your going to be snow in pretty soon.
Got to get busy on that GE cabinet. I found
some small brads so I can nail the top back down.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

By the time I fixed the hole It would have cost me way more than the junk set, I needed a knob and I took the case. I still have a chassis that is not too bad though it has the small tubes instead of the Octal like the one we fixed. 

Paul

Tubetalk1
#4

Nice!

What's that big white console The Emerson was sitting on for the pictures?  Icon_wink

I don't hold with furniture that talks.
#5

I would give it back, lots of memories of his dad. David
#6

(03-14-2018, 12:21 PM)EdHolland Wrote:  Nice!

What's that big white console The Emerson was sitting on for the pictures?  Icon_wink



That is my Whirlpool console sounds good especially if change was left in your pocket. Icon_lol

Paul

Tubetalk1




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 610B oscillator wiring
I don't know what you are referring to when you say "tube cathode ground". Ground is a connection to the chass...RodB — 05:56 PM
Zenith H725
Good points, Arran. I haven't encountered this problem with any other radio (all earlier vintages), so am learning here....EdHolland — 05:32 PM
Zenith H725
Ed; One thing that I will say about these is that Brand Z was considerate enough to make these mica caps easily acces...Arran — 02:34 PM
Philco 610B oscillator wiring
Do you know what run # your chassis is? It took me a while to find what you were basing updates/modification on as I did...Radioroslyn — 07:34 AM
Need to purchase some accessories for restoration of my Old Philco Radio
COLLEAGUES, Thank you all for such good and important suggestions as how to find good replacement parts. I will go fo...palonso — 07:05 AM
Zenith H725
Here's what the inside of AM IFT2 looked like, and the other pic shows the discs I made to take place of the mica and ke...EdHolland — 07:40 PM
Zenith H725
IF2 will need replacement caps. The arcing was severe enough that the mica is pitted and holed where the HT flashed over...EdHolland — 04:04 PM
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM
My Philco 37-116 Restore
Are you measuring relative to the centertap or the GND?morzh — 11:57 PM
Philco 610B oscillator wiring
Still not clear on the wiring interface between the 6A7 and oscillator. After refering to the available schematics and s...Tubester — 07:18 PM

[-]
Who's Online
There are currently 1844 online users. [Complete List]
» 2 Member(s) | 1842 Guest(s)
AvatarAvatar

>