Posts: 189
Threads: 22
Joined: Aug 2018
City: Kewanee
State, Province, Country: Illinois
I picked up a nice old recapped Eico 324 Signal Generator, but without the RF output cable. Does anyone know where I can purchase one that will work for this? Is there a way to convert it to some other style? What are my options? Thank you for your input in advance.
1929 Victor R-32, 1933 60L, Phil 40-158, Phil 42-400X, Phil 47-1230 Radio/Phono,, 1950 Phil TV t-1104, Air King 4000, Philco 41-105, Philco 37-675, RCA Victor 9K2, PT-50, Phil 54C, PT-44 Cabinet, Phil 118X Cabinet
Gregg 
Posts: 4,707
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
It probably used a shielded (not coax) cable with an Amphenol connector, basically like and old fashioned microphone. There are available, at least NOS and used ones are, look it up on fleabay, or on Mouser or Digikey's sites.
Regards
Arran
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
What you are seeking is a Switchcraft 2501F. You could swap it over to another style of connector like a bnc or so-239 but if you don't have any other cables that already have these connector on them I wouldn't bother.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 189
Threads: 22
Joined: Aug 2018
City: Kewanee
State, Province, Country: Illinois
Thanks Terry!
1929 Victor R-32, 1933 60L, Phil 40-158, Phil 42-400X, Phil 47-1230 Radio/Phono,, 1950 Phil TV t-1104, Air King 4000, Philco 41-105, Philco 37-675, RCA Victor 9K2, PT-50, Phil 54C, PT-44 Cabinet, Phil 118X Cabinet
Gregg
Posts: 667
Threads: 11
Joined: Sep 2014
City: Bellmawr, NJ
E-Bay sell them,,,,just like NOS
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Philco 38-7 Oscillation
|
| Will do, thank you.tludka — 10:26 AM |
|
Philco 38-7 Oscillation
|
| As to your oscillation issue I would align the IF transformers. That may solve the problem. You also would want to check...Radioroslyn — 10:22 AM |
|
Philco 38-7 Speaker
|
| Thank you, I will check this out, I do have some shields I can place around the specific tubes. I searched the four que...tludka — 10:18 AM |
|
Philco 38-7 Speaker
|
| Also, check if any wires going to Grid Caps of the tubes that are supposed to be INSIDE of their respective shields (if ...morzh — 09:54 AM |
|
Philco 38-7 Oscillation
|
| Usually in this forum, when we discuss a radio, we do not multiply threads. You already have a thread on this.
If you wa...morzh — 09:27 AM |
|
identify very thin wire for replacement on 37-640
|
| You can possibly use a heatshrink tubing.
If you decide to replace the wire, anything gauge 24, 300V rated will do (it ...morzh — 09:25 AM |
|
identify very thin wire for replacement on 37-640
|
| Happy Thanksgiving,
I have attche a photo of a very thin wire with black plastic-looking insulation(some of it has com...georgetownjohn — 09:14 AM |
|
Philco 60 Squealing
|
| I got my signal tracer out to see if I could tell at what stage the squeal was coming from. It is present on the plate o...dconant — 09:07 AM |
|
Philco 16B Parts
|
| The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM |
|
Philco 38-7 Oscillation
|
| I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM |
|
Who's Online
|
There are currently 3414 online users. [Complete List]
» 1 Member(s) | 3413 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
