1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Quick help
1230AM
Junior Member
**
Posts: 8
Threads: 3
Joined: Feb 2020
City: Louisville State, Province, Country: KY
#1

02-11-2020, 12:41 PM
At the risk of a violation - In addition to my prior Low AM Volume question, (On a Philco) I have a non-Philco radio with a Numite Condenser Cat. No. AT 8450 reading cap.8 and 450v.  Just to be clear, is this merely an 8mf capacitor?

Radio has a hum and this is the only cap not replaced.  Its a large one and I suspect this to be the issue.

Thank you and my apologies for posting a non-Philco question.....But this hopefully is generic and will be the last non-Philco question I ask.
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,283
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

02-11-2020, 12:49 PM
I would think that it's an 8mfd. An .8 would pretty small in physical size by comparison. 10mfd would be a suitable replacement as I don't know if the 8's are a common value anymore. Old school tubular 8mfd@450v would be abt 1" in dia and 2 to 3" long.
Here @ the Philco Phorum we are a non discriminatory radio phorum however we do have a special section for "other radios"
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 02-11-2020, 12:55 PM by Radioroslyn.)
Find
1230AM
Junior Member
**
Posts: 8
Threads: 3
Joined: Feb 2020
City: Louisville State, Province, Country: KY
#3

02-11-2020, 02:32 PM
Thanks!  What you describe would be it.  Thanks again for the confirmation.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
I can't remember, but there was a particular product for loosening glue on the more modern "spiders", used pos...MrFixr55 — 09:43 PM
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM

[-]
Who's Online
There are currently 1953 online users. [Complete List]
» 2 Member(s) | 1951 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration