Posts: 15,510
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
Aligned the set.
The procedure is well-hidden, but I unearthed sometging from the 89 Rider article.
Very simple alignment. Just IF (3 padders) and 1500 kHz. The lower frequency just aligned itself.
Now have to put it back together and clean up the exterior a bit.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 09-01-2020, 07:45 PM by morzh.)
Posts: 1,185
Threads: 49
Joined: Oct 2017
City: Allendale, MI
You're standing on your head to take that pic!
Posts: 15,510
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
:
No. This is the way it is, the chassis is for the LZ so it is oriented this way so when itis horizontal, the wheel is upside down.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 3,131
Threads: 56
Joined: Apr 2011
City: Lexington, KY
So far so good Mike 
Looking forward to a picture when it's back in the cabinet...
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Posts: 1,185
Threads: 49
Joined: Oct 2017
City: Allendale, MI
"This is the way it is, the chassis is for the LZ so it is oriented this way so when itis horizontal, the wheel is upside down."
That's right, it's a chair side. Duh!
Posts: 15,510
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
I took the picture of what I saw while giving the chassis one last look:
Remember when I said this chassis is ...tight?
Yes. This tight. The first cap of the tone control is practically touching the grounded electrolytics mounting bracket. And the voltage there is the plate voltage. Safe, as all it would result in is the first cap getting engaged. But....so I had to bend it out. It is possible the bracket got moved a bit when put back in place. Still too close.
Anyhow, I put back the rear cover to the speaker cabinet and gave it a GoJo bath.
I also sprayed the asbestos-lined metal screen with hi-temp finish, same I did for the Transoceanic.
Tomorrow hopefully I could reassemble the chassis into its cabinet, give the cabinet a GoJo bath, and it should be over then.
I have to say, it sounds really good. Not 38-690 good, but really, really good.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 09-02-2020, 08:03 PM by morzh.)
Posts: 15,510
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
Well. I gave the radio cabinet GoJo wipe.
I made some pictures, but this is with the tablet and not a very good lighting.
This said, of course, the radio cabinet could use refinishing, though the speaker cabinet is fine the way it is. Not ideal but it looks decent to be preserved.
The sound is good. I like it. I took it out from my workshop to put with the general population. Too bad the space in my basement starts shrinking, and I do not think my wife wants it upstairs.
It will have to live in the basement for now.
It is no longer upside down.
This concludes it for now.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 09-03-2020, 08:00 PM by morzh.)
Posts: 3,131
Threads: 56
Joined: Apr 2011
City: Lexington, KY
Looks good Mike
They're survivors and a few blemishes here and there after all they've been through can be overlooked.
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Posts: 1,523
Threads: 240
Joined: Sep 2012
City: West Bend, Wisconsin
Excellent work, Mike! There's too much good finish left to merit refinishing. Leave those "battle scars of a bygone era" intact...it gives it some extra character!
Greg V.
West Bend, WI
Member WARCI.org
Posts: 15,510
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
My thought exactly.
I wish I had some sort of account somewhere that allows videos. Unfortunately U-toob is no longer an option.
This is one good sounding radio.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Bakelite crack repair - what is best epoxy?
|
| Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM |
|
Jackson 665 j2 schematic request
|
| Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM |
|
Jackson 665 j2 schematic request
|
| Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM |
|
Looking for place to donate unique Philco Philco J-1930 Prototype
|
| >>I'll write to the Henry Ford.
I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM |
|
Philco 48-200 alignment questions
|
| Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM |
|
Looking for place to donate unique Philco Philco J-1930 Prototype
|
| Thanks for the suggestions. I'll write to the Henry Ford. That would certainly make sense since by the time this prod...jeibner — 11:49 AM |
|
Looking for place to donate unique Philco Philco J-1930 Prototype
|
| For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option.
The obvious ...GarySP — 11:39 AM |
|
Help with Readrite 410 tube tester
|
| Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM |
|
Looking for place to donate unique Philco Philco J-1930 Prototype
|
| We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM |
|
Philco 89B code 123 newbie
|
| I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1"...Radioroslyn — 09:28 AM |
|
Who's Online
|
| There are currently no members online. |
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
