Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 38-12 Cabinet Strip
#16

   
So...just figured I'd share what the radio looks like as I received it this week.  Certainly, there's a lot of cabinet work to do, and I'm a little concerned about what might be hidden under all that dark stain, lacquer, etc.  In addition, the dial is merely a photocopy of an actual dial, the pointer needle is incorrect, the knobs are incorrect, and the speaker fabric will likely need to be replaced.

Luckily, I was able to order a repro dial from Radio Daze, but am having trouble locating the correct pointer, knobs, and fabric.  I know this is probably elementary to most of you, so appreciate any recommendations on sources for these parts.
#17

The grille cloth is correct. It looks okay in the photo - is something wrong with it?

--
Ron Ramirez
Ferdinand IN
#18

Well, it is much dirtier than it appears in the photo, and won't match a fully restored cabinet very well, unless I can find a way to clean it carefully.  Parts of it are very delicate and will likely fall apart when I remove it anyway. Just want to have a decent backup if/when that occurs.

Finally located the correct knobs, so just hoping someone can recommend a source for the fabric and pointer...especially the pointer, as I'm learning that these are as scarce as hen's teeth!




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM

[-]
Who's Online
There are currently 1396 online users. [Complete List]
» 1 Member(s) | 1395 Guest(s)
Avatar

>