1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 45 Tone Control Question
Guest
Unregistered
 
#1

08-12-2007, 05:57 PM
I've pretty much finished electronic restoration on 45 chassis. I took apart the bakelite block tone control module. Unfortunately, my RIDER schematic does not give me the values of the three caps inside the block. Can anyone tell me the values and what order they're wired in?
Thanks,
Britt
Chesapeake, VA
Terry Judkins
Member
***
Posts: 91
Threads: 5
Joined: Oct 2005
City: Atlanta GA
#2

08-12-2007, 06:22 PM
The values are 0.01Uf, 0.02uF and 0.001uf.
The .001 is directly across to rotor common (ground) and is not switched. The .01 is connected to the center contact and the .02 is connected to the third contact. The first position is off and has no capacitor.
[Image: http://home.comcast.net/~suptjud/Philco4...ontrol.JPG]
Kind regards,
Terry
http://home.comcast.net/~suptjud/
"Life is simpler when you plow around the stump."
Website Find
Guest
Unregistered
 
#3

08-13-2007, 01:25 PM
Terry...

I'm electronically challenged, but you made it very clear on how to wire the caps in....

THANKS,

Britt Abbott
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Rare zenith 6s137 restore
Hi Fred, I get things to work, but what you, Russ, RadioSvit and many others on the Phorum do with cabinet and chassis...MrFixr55 — 09:02 AM
PT-6 antenna connections
Hi Bridcarl +1 on the others.  Pin 6 of the 7C6 is the AVC Diode so it is appropriate that that pin 4 of the coil con...MrFixr55 — 07:30 AM
462ron
Joseph, this is beyond awesome. A lot of thought and engineering went into this and you hit a home run! Now I must save ...462ron — 07:27 AM
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM

[-]
Who's Online
There are currently 4203 online users. [Complete List]
» 2 Member(s) | 4201 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration