1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Lamp for Philco 46-427
joegatto
Junior Member
**
Posts: 7
Threads: 2
Joined: Aug 2012
City: South Carolina
#1

03-27-2013, 01:50 PM
The schematic for this set calls for a I100 bulb for the panel light. It is a bayonet type but not a 44 or 47 6 volt bulb. Anyone knowe what it is? Thanks - Joe jdgatto@earthlink.net
Find
Carl Travis
Member
***
Posts: 205
Threads: 6
Joined: Jun 2006
City: Moundsville State, Province, Country: WV
#2

03-27-2013, 02:09 PM
Joe,
P/N 34-2068 is supposed to be a type 47 bulb:
http://www.philcorepairbench.com/lamps.htm
Carl
Northern Panhandle, WV
Find
joegatto
Junior Member
**
Posts: 7
Threads: 2
Joined: Aug 2012
City: South Carolina
#3

03-27-2013, 02:54 PM
Thanks Carl. I see my mistake now. When I first tried a 47 it blew out immediately, probably a fluke. I then went to a 44 but that draws too much current. Will go to radio shack and pick up another 47 and try again. Joe
Find
Chuck Schwark
Phorum Expert
*****
Posts: 1,703
Threads: 55
Joined: Sep 2005
City: Evanston, IL
#4

03-28-2013, 01:26 PM
I100 is the schematic/parts listing designator - Indicator (lamps) 100.

Just like L for coils, T for transformers, C for caps, etc......
Chuck
Chuck Schwark,
The Philco Repair Bench
[Image: http://www.philcorepairbench.com/images/philog3tiny.gif]
http://www.philcorepairbench.com
Website Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration