Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Gift from FIL. sweet
#16

A little OT but I know there is a model 66 in the MB cabinet yet it is listed that there is only a 60MB. Is the 66 a MB??
Terry
#17

Nope, the 66 in that cabinet was sold as a 66B. The 66B soon became a cathedral:

http://www.philcoradio.com/gallery/1935b.htm#e

I suspect this was Philco's way of using up excess 60MB cabinets.

--
Ron Ramirez
Ferdinand IN
#18

Welcome to the Phorum.

For now, you can look up the data sheets for the tubes and check continuity on the filaments.

However, before you get wrapped around the axle with tubes (which are probably good anyway) start replacing all of the capacitors and any resistors that are out of spec.

It's not how bad you mess up, it's how well you can recover.
#19

Keith great looking radio. Good luck with it , go slow and have fun doing it....And most of all welcome to the forum!
#20

If you want to do a quick test on the tubes pull out the 80 tube. Plug the set in and snap it on. Look at the tops of the tubes and you should see a small orange glow if the heater is OK. Do not do this with the 80 installed. You can damage the set if you haven't replaced the caps in it. As for the 80 tube use an ohm meter across the two fat pins on the bottom of the tube. Should show a very low resistance across these two pins. If not tube is bad.
GL
Terry
#21

Just want to call to your attention all the great advice from some great folks here on the Phorum.

You meet the best people here, it's almost like family, from Ron on down.

BTW, Ron is a PhD. (Doctor of Philcology)Icon_thumbupIcon_thumbupIcon_thumbup




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
I can't remember, but there was a particular product for loosening glue on the more modern "spiders", used pos...MrFixr55 — 09:43 PM
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM

[-]
Who's Online
There are currently 1909 online users. [Complete List]
» 2 Member(s) | 1907 Guest(s)
AvatarAvatar

>