Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
Posts: 599
Threads: 24
Joined: Jan 2014
City: Edmonton AB CA
Dan, do you have a source for those 24 volt 30ma bulbs?
Gregb
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
I am going to check out my sources and see where I bought this one.
I have tried industrial electrical suppliers in the past.
The one I am thinking of did have 24 volt bulbs but I don't know the MA.. I will check into it and post here on the forum.. Dan
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
I did some research for those bulbs and I found a place called Bulb Town...www.bulbtown.com. I can get the bulbs and they cost $8.64 Canadian for 5 bulbs. I was going order 5 but the shipping came to over $30.00 so I did not order any..
I found the bulbs by looking under ''bulbs by volts ''at the bottom of that page.. The bulb was 24 volt,,,35MA. It has an E10 base[screw]
If you were to order $50.00 or more , the shipping is free.
I could not find anyplace in Calgary that had any..
Posts: 4,707
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
Try Mouser or WJOE radios, they seem to carry some obscure bulbs, I got some fuse lamps for my Marrantz from WJOE. One of the common faults these Deforest Crosley's have are the crumbling dial lamp leads, particularly on the one that rotate, that was a popular gimmick even on the later models, my 1938 Brahms model uses something similar even though the dial is rainbow shaped.
Regards
Arran
http://www.wjoe.com/all_lamps.htm
(This post was last modified: 06-24-2014, 04:13 PM by Arran.)
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
Posts: 1,402
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO
That is a sharp looking radio 
Steve
M R Radios C M Tubes
Posts: 479
Threads: 73
Joined: Mar 2012
City: Riverside, CA
Looks absolutely beautiful, great job!!!
- Geoff
Posts: 15,825
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
This is just majestic!
This dotted ornament around the dial, is it inlay or photo?
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
That inlay around the dial is actual wood inlay, the same as the inlay around the sides.
Posts: 1,463
Threads: 97
Joined: Jul 2012
City: Poughkeepsie, N.Y.
I just love it! Great job how does she play?
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
It plays just'''' alright.''''.. But when I turn the sensitivity control all the way to the right the volume goes right down. I just don't know enough about it to do any more so I plan on leaving it that way.
It does pick up all the stations and the tone and volume work fine.
Posts: 79
Threads: 13
Joined: Feb 2014
City: Bristol, RI
That's a beauty! Very sharp set. I'd have a hard time handing that one over for those windows..
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Dan a nice job on an absolutely lovely radio. Congrats.
Jerry
A friend in need is a pest! Bill Slee ca 1970.
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Philco 16B Parts
|
| The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM |
|
Philco 38-7 Oscillation
|
| I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM |
|
Philco 38-7 Speaker
|
| I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM |
|
Philco 60 Squealing
|
| I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM |
|
Philco 42-390, code 121 speaker
|
| These speakers pop up on eBay regularly, even if at bloated prices.
Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM |
|
Philco 38-7 Speaker
|
| The put-put is not like the speaker problem.morzh — 08:29 PM |
|
Mission Bell Model 19A Car Radio
|
| Hello everyone,
As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM |
|
Philco 60 Squealing
|
|
Wondering if I did it backwards.
If a coil was wound backwards, the oscillator would not work at all.
Old school...Chas — 07:23 PM |
|
Philco 38-7 Speaker
|
| 4-ohm speaker. Black, Green leads.tludka — 07:00 PM |
|
Philco 42-390, code 121 speaker
|
| #87 on the schematic.
This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM |
|
Who's Online
|
There are currently 2176 online users. [Complete List]
» 1 Member(s) | 2175 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
