Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Remler wood console
#1

   

I found this on craigslist for $80. I can't seem to find any info on Remler wood consoles. I found lots of stuff about their table bakelite units. Anybody have any info about this? And maybe if it's a good buy?

Thanks,

Pat
#2

If it is clean inside...maybe. Provided the speaker is good.
#3

Looks like it might be an amputee though...

No matter where you go, there you are.
#4

It has a short.............................cabinet.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#5

(11-08-2014, 08:21 PM)Phlogiston Wrote:  It has a short.............................cabinet.

So do I. But I think I'll pass. Thanks to you all.
#6

  Given the weekend warrior refinish, the missing legs, broken escutcheon, broken speaker grille, mystery knobs, $80 is way to much, maybe $30-40 tops, if it had everything still in the back, but preferably less. As I keep explaining to people, it's the restoration costs in time and money that nails you, sometimes even if the radio is free it's too much.
Regards
Arran
#7

(11-09-2014, 02:11 AM)Arran Wrote:    Given the weekend warrior refinish, the missing legs, broken escutcheon, broken speaker grille, mystery knobs, $80 is way to much, maybe $30-40 tops, if it had everything still in the back, but preferably less. As I keep explaining to people, it's the restoration costs in time and money that nails you, sometimes even if the radio is free it's too much.
Regards
Arran

I agree 100%. My time isn't worth much because it's a hobby, and caps and resistors are cheap, but the rest can cost an arm and a leg, and you'll never be able to sell it for more than you have invested. I used to restore classic cars as a hobby, and if you weren't careful, you could put $25,000 into a car, and only sell it for $20,000. At least with this hobby, my bank account doesn't suffer as much, and my wife lets me sleep in the bedroom rather than the garage.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 3766 online users. [Complete List]
» 2 Member(s) | 3764 Guest(s)
AvatarAvatar

>