Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

42-1008P Stain *Cabinet Done*
#31

So here is what I am wondering about.


[Image: http://i1289.photobucket.com/albums/b519...edp7bu.jpg]

I believe the unit had original finish on it so from what I can see the trim piece that comes up along side the door is dark like other dark areas (red oval) and then hits a transition or swirl into that flat side piece (orange circle) and then the flat side (blue circle) is just about as toned as the face.

Does that seem to be what I should be going after?
#32

Just when you think you have a section looking good the sun hits it just right and you see a bad sanding job Icon_sad

Going to move on and figure out if I want to worry about fixing it.

I'm not all that good at this wood stuff.
#33

(03-28-2015, 01:16 PM)Edisla Wrote:  Just when you think you have a section looking good the sun hits it just right and you see a bad sanding job Icon_sad

Going to move on and figure out if I want to worry about fixing it.

I'm not all that good at this wood stuf
Edisla, don't give up. You have been working hard on it. Maybe just sand a little more with finer sand paper and it will look nice when covered with clear, etc. Icon_smile Don't forget to always sand WITH the grain.
#34

I wont give up.

I may give in a little but will not give up.
#35

Well here is how it came out.

Not exactly how I wanted it but it is close enough.

Before

[Image: http://i1289.photobucket.com/albums/b519...vxg1z2.jpg]

After
[Image: http://i1289.photobucket.com/albums/b519...cvak9q.jpg]
#36

Lookin Nice ...
#37

Yes it does look nice... Icon_thumbup Icon_thumbup
#38

looks fine to me great job Icon_clap Icon_thumbup
sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently no members online.

>