Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Phonograph with Philco by Radiobar
#16

Since I sorta got this thread off-topic for a bit, I'm going to start a new thread dedicated only to the Phonograph with Philco by Radiobar.

Pat
#17

Here are some pics of the unit sent to me by the PO. He just delivered the unit to me yesterday, so I haven't had a chance to go through it yet. Someone out there MUST have more information on this. All I can find is what Ron has, including the Mulholland Press info. 

Cabinet made and marketed by Radiobar, a Philco 38-3 chassis, and a Capehart automatic record changer.
[Image: http://i1367.photobucket.com/albums/r796...6mu61p.jpg]
[Image: http://i1367.photobucket.com/albums/r796...3atcur.jpg]
[Image: http://i1367.photobucket.com/albums/r796...yhieir.jpg]
[Image: http://i1367.photobucket.com/albums/r796...ptvf1d.jpg]
#18

WOW  that looks great Icon_thumbup
looks pretty good condition too.  maybe just touch up ?
you could always send out to east coast if you don`t have room for it Icon_mrgreen
sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#19

(07-25-2015, 12:30 PM)sam Wrote:  WOW  that looks great Icon_thumbup
looks pretty good condition too.  maybe just touch up ?
you could always send out to east coast if you don`t have room for it Icon_mrgreen
sam

Yeah Sam, I think you're right. Maybe just touch up. Except for the lid. The inside of the lid is pristine, including the felt, but the top HAS to be refinished.

And I DON'T have room for it, so it will be on ebay when I'm done. 'Course shipping wouldn't be too cheap. It measures 42x37x19, and has to weigh more than 100 lbs.

Pat 
#20

Nice restorations! I merged your two threads as they are primarily both about the same set.
#21

(07-25-2015, 04:12 PM)klondike98 Wrote:  Nice restorations!  I merged your two threads as they are primarily both about the same set.

O.K. Thanks

Pat




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
Apparently there is a new Philco Repair Bench found at https://philcoradio.com/repairbench/ When I try to go to order a ...dconant — 12:00 PM
Philco 60 Squealing
Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM
American Bosch Model 802 auto radio
Hi Arran ,  Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM

[-]
Who's Online
There are currently no members online.

>