Pilot G-674 restoration

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Pilot G-674 restoration

Arran
Phorum Expert

Posts: 4,639
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA

#16

02-06-2016, 02:07 AM

Kirk;
It looks like you will need to pick up some poplar and make a few structural replacement parts on that cabinet, what you can see looks bad enough but there is probably more damage where you can see it yet. Where did they leave this set, on a dirt floor?
Regards
Arran

Find

« Next Oldest | Next Newest »

Messages In This Thread

Pilot G-674 restoration - by OldRestorer - 01-27-2016, 03:58 PM

RE: Pilot G-674 restoration - by OldRestorer - 01-27-2016, 04:00 PM

RE: Pilot G-674 restoration - by klondike98 - 01-27-2016, 04:09 PM

RE: Pilot G-674 restoration - by KCMike - 01-27-2016, 04:32 PM

RE: Pilot G-674 restoration - by mikethedruid - 01-27-2016, 04:34 PM

RE: Pilot G-674 restoration - by Kenneth F. Besso Jr. - 01-27-2016, 04:45 PM

RE: Pilot G-674 restoration - by OldRestorer - 01-27-2016, 07:01 PM

RE: Pilot G-674 restoration - by sam - 01-27-2016, 07:22 PM

RE: Pilot G-674 restoration - by OldRestorer - 01-27-2016, 07:32 PM

RE: Pilot G-674 restoration - by Paul Philco322 - 01-27-2016, 08:55 PM

RE: Pilot G-674 restoration - by OldRestorer - 01-28-2016, 09:11 AM

RE: Pilot G-674 restoration - by leftwing25 - 02-03-2016, 02:33 PM

RE: Pilot G-674 restoration - by Arran - 02-06-2016, 02:03 AM

RE: Pilot G-674 restoration - by OldRestorer - 02-03-2016, 03:49 PM

RE: Pilot G-674 restoration - by leftwing25 - 02-03-2016, 04:09 PM

RE: Pilot G-674 restoration - by Arran - 02-06-2016, 02:07 AM

RE: Pilot G-674 restoration - by OldRestorer - 02-06-2016, 06:23 AM

RE: Pilot G-674 restoration - by leftwing25 - 02-06-2016, 12:46 PM

RE: Pilot G-674 restoration - by OldRestorer - 02-07-2016, 01:54 PM

RE: Pilot G-674 restoration - by leftwing25 - 02-07-2016, 03:24 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

Who's Online

There are currently 3622 online users. [Complete List]
» 2 Member(s) | 3620 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me