Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Pilot G-674 restoration
#17

I had purchased it from an antique store so it is unknown about storage. It was probably a dry storage but could have been a dirt floor. The termites were long gone and I did go up into the bad areas. Yes, some go right up to the veneer but they didn't touch the veneer, I will epoxy fill the areas that are up against veneer and throw in some new wood in the other spots. That wont happen until spring though....and after doing the guys cabinets...
Me

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6


Messages In This Thread
Pilot G-674 restoration - by OldRestorer - 01-27-2016, 03:58 PM
RE: Pilot G-674 restoration - by OldRestorer - 01-27-2016, 04:00 PM
RE: Pilot G-674 restoration - by klondike98 - 01-27-2016, 04:09 PM
RE: Pilot G-674 restoration - by KCMike - 01-27-2016, 04:32 PM
RE: Pilot G-674 restoration - by mikethedruid - 01-27-2016, 04:34 PM
RE: Pilot G-674 restoration - by OldRestorer - 01-27-2016, 07:01 PM
RE: Pilot G-674 restoration - by sam - 01-27-2016, 07:22 PM
RE: Pilot G-674 restoration - by OldRestorer - 01-27-2016, 07:32 PM
RE: Pilot G-674 restoration - by Paul Philco322 - 01-27-2016, 08:55 PM
RE: Pilot G-674 restoration - by OldRestorer - 01-28-2016, 09:11 AM
RE: Pilot G-674 restoration - by leftwing25 - 02-03-2016, 02:33 PM
RE: Pilot G-674 restoration - by Arran - 02-06-2016, 02:03 AM
RE: Pilot G-674 restoration - by OldRestorer - 02-03-2016, 03:49 PM
RE: Pilot G-674 restoration - by leftwing25 - 02-03-2016, 04:09 PM
RE: Pilot G-674 restoration - by Arran - 02-06-2016, 02:07 AM
RE: Pilot G-674 restoration - by OldRestorer - 02-06-2016, 06:23 AM
RE: Pilot G-674 restoration - by leftwing25 - 02-06-2016, 12:46 PM
RE: Pilot G-674 restoration - by OldRestorer - 02-07-2016, 01:54 PM
RE: Pilot G-674 restoration - by leftwing25 - 02-07-2016, 03:24 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>