Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Help in Identifying radio
#16

(07-27-2016, 03:50 PM)klondike98 Wrote:  So you need to find a 38-89 chassis or its equivalent.  That would mean any of the following radios with a working chassis (or even the chassis without the cabinet since the chassis in these are the same) would fill the bill: 37-89B (table model), 37-89F (console), 38-89B (table model), or 38-89K (console).  

Borrowing might be difficult since shipping is always a somewhat risky business but you never know until you ask.  You can add a note in the "Wanted Ads" section to buy or borrow a set and see who might have something. There are a few 37-89s on ebay at the moment even some that claim to be working (that sometimes means that the dial lamp glows or you can hear static).  

There is the Northwest Vintage Radio Society that is only 2 hours south of you that might have someone who owns one of the above radios and could help you out.  Unfortunately I don't know anyone in that group but you could give them a call to see what they might have.  Most folks in this hobby are pretty friendly and always interested in showing off their collections.

If you are trying to recreate the radio call that the lady believes she heard and looking for the same set to use as part of the experiment, keep in mind that restored sets today may vary quite a bit in performance depending on how well they were restored.  Reception on short wave can be very dependent on the atmospheric conditions that cause the radio signals to bounce off the atmosphere and travel long distances (I'm no expert on this, just general info. )    OK..probably more than you wanted to know ...
Great response, thanks.
I will check with the NW Vintage Radio Society. Yes we are going to re-create the transmission.  Anyone know what the sun activity was on July 2, 1937?  Does anyone have any thoughts on how much change there is in the daily, monthly, and yearly activity in atmospheric conditions as it relates to receiving long distance radio transmissions?  
 


Messages In This Thread
Help in Identifying radio - by lgkinney - 07-24-2016, 01:26 AM
RE: Help in Identifying radio - by OldRestorer - 07-24-2016, 08:45 AM
RE: Help in Identifying radio - by klondike98 - 07-24-2016, 08:46 AM
RE: Help in Identifying radio - by lgkinney - 07-24-2016, 06:33 PM
RE: Help in Identifying radio - by klondike98 - 07-24-2016, 07:49 PM
RE: Help in Identifying radio - by Ron Ramirez - 07-24-2016, 08:58 PM
RE: Help in Identifying radio - by lgkinney - 07-27-2016, 02:54 PM
RE: Help in Identifying radio - by klondike98 - 07-24-2016, 09:18 PM
RE: Help in Identifying radio - by lgkinney - 07-27-2016, 02:46 PM
RE: Help in Identifying radio - by Radioroslyn - 07-25-2016, 01:51 PM
RE: Help in Identifying radio - by morzh - 07-25-2016, 02:27 PM
RE: Help in Identifying radio - by Ron Ramirez - 07-26-2016, 12:39 PM
RE: Help in Identifying radio - by klondike98 - 07-27-2016, 03:50 PM
RE: Help in Identifying radio - by lgkinney - 07-27-2016, 04:06 PM
RE: Help in Identifying radio - by klondike98 - 07-27-2016, 04:32 PM
RE: Help in Identifying radio - by GarySP - 07-27-2016, 05:18 PM
RE: Help in Identifying radio - by lgkinney - 07-28-2016, 12:06 AM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
As far as I know, the Repairbench does not work, and has not been working in a while. Chuck (we had that campaign looki...morzh — 01:33 PM
Radio city products 664 schematic request
Need a schematic or manual for the 664. The 663 may be similar.daveone23 — 12:38 PM
New Philco Repair Bench
Thanks Gary.dconant — 12:16 PM
New Philco Repair Bench
I tried accessing the site through our library and got the same response. It's reported to our tech gurus. GaryGarySP — 11:50 AM
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM

[-]
Who's Online
There are currently 7318 online users. [Complete List]
» 1 Member(s) | 7317 Guest(s)
Avatar

>