1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
philco470/490
mg34.42
Member
***
Posts: 87
Threads: 34
Joined: Dec 2013
City: Tulsa, OK
#23

07-28-2016, 08:03 AM
(07-28-2016, 07:26 AM)Ron Ramirez Wrote:  Nope, other than keeping a close watch on the auction site...

unless...

You might contact Ed (Blacksmith) at Renovated Radios. He is a Phorum member - just send a PM to blacksmith, or go to his website and scroll all the way down the home page to get his contact info.

My point is...if Ed is willing to reproduce this part...I'm willing to send the "Made in U.S.A." escutcheon from my set to him to be reproduced.

OK I'll send a message to see what he can do 
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 470 - by Radioroslyn - 07-18-2016, 01:32 PM
RE: philco470/490 - by sam - 07-19-2016, 10:15 AM
RE: philco470/490 - by Radioroslyn - 07-19-2016, 01:35 PM
RE: philco470/490 - by sam - 07-19-2016, 02:11 PM
RE: philco470/490 - by mg34.42 - 07-19-2016, 02:24 PM
RE: philco470/490 - by sam - 07-19-2016, 02:39 PM
RE: philco470/490 - by mg34.42 - 07-19-2016, 07:12 PM
RE: philco470/490 - by mg34.42 - 07-19-2016, 07:20 PM
RE: philco470/490 - by Ron Ramirez - 07-19-2016, 07:32 PM
RE: philco470/490 - by mg34.42 - 07-19-2016, 07:51 PM
RE: philco470/490 - by Ron Ramirez - 07-19-2016, 08:45 PM
RE: philco470/490 - by mg34.42 - 07-27-2016, 09:57 PM
RE: philco470/490 - by Eliot Ness - 07-27-2016, 11:53 PM
RE: philco470/490 - by mg34.42 - 07-28-2016, 05:43 AM
RE: philco470/490 - by Ron Ramirez - 07-28-2016, 07:26 AM
RE: philco470/490 - by mg34.42 - 07-28-2016, 08:03 AM
RE: Philco 470 - by Ron Ramirez - 07-18-2016, 02:34 PM
RE: philco470/490 - by mg34.42 - 07-19-2016, 02:22 PM
RE: Philco 470 - by Ron Ramirez - 07-18-2016, 06:09 PM
RE: Philco 470 - by Radioroslyn - 07-18-2016, 06:20 PM
RE: Philco 470 - by Ron Ramirez - 07-18-2016, 06:31 PM
philco470/490 - by mg34.42 - 07-18-2016, 09:08 PM
RE: philco470/490 - by Radioroslyn - 07-19-2016, 05:39 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 3957 online users. [Complete List]
» 3 Member(s) | 3954 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration