1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 1 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
PhrankenPhilco 610-630
Radioroslyn
Phorum Expert
*****
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#4

08-07-2016, 05:35 PM
Interesting! Rider's says both are 1140 ohms, which make more scents.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
PhrankenPhilco 610-630 - by kc5gym - 08-07-2016, 03:40 PM
RE: PhrankenPhilco 610-630 - by Radioroslyn - 08-07-2016, 05:06 PM
RE: PhrankenPhilco 610-630 - by KCMike - 08-07-2016, 05:23 PM
RE: PhrankenPhilco 610-630 - by Radioroslyn - 08-07-2016, 05:35 PM
RE: PhrankenPhilco 610-630 - by klondike98 - 08-07-2016, 06:01 PM
RE: PhrankenPhilco 610-630 - by kc5gym - 08-07-2016, 06:37 PM
RE: PhrankenPhilco 610-630 - by kc5gym - 08-07-2016, 08:02 PM
RE: PhrankenPhilco 610-630 - by Radioroslyn - 08-07-2016, 08:51 PM
RE: PhrankenPhilco 610-630 - by kc5gym - 08-08-2016, 05:33 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

[-]
Who's Online
There are currently 3840 online users. [Complete List]
» 1 Member(s) | 3839 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration