Thread Rating:
  • 1 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5

PhrankenPhilco 610-630
#8

Ok so what will happen if you use the spkr as is is it will raise your HV a bit because it has a low dc resistance. We don't know what the inductance is which will affect it ability to filter out 60cy hum so you may have to increase the value of your second filter cap. The high B voltage probably not enough to worry about.

The dc resistance of the output transfromer doesn't mean much what does is the ac impedance. Since it is designed to match the plate impedance of the 42 tube (7000 ohms) to the philco spkrs voice coil your all set. You don't need to change it.

Sorry abt ur license. If you have a current one w/another call you may be able to get ur old call back though the vanity call sign program. If you have been expired for a good while ( I think the rule is 2 yrs) you have to take the test over again. QRZ has a service that you can sign up for (free) and they will send you an email a few months before you expire (license that is not you the person).
GL

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
PhrankenPhilco 610-630 - by kc5gym - 08-07-2016, 03:40 PM
RE: PhrankenPhilco 610-630 - by Radioroslyn - 08-07-2016, 05:06 PM
RE: PhrankenPhilco 610-630 - by KCMike - 08-07-2016, 05:23 PM
RE: PhrankenPhilco 610-630 - by Radioroslyn - 08-07-2016, 05:35 PM
RE: PhrankenPhilco 610-630 - by klondike98 - 08-07-2016, 06:01 PM
RE: PhrankenPhilco 610-630 - by kc5gym - 08-07-2016, 06:37 PM
RE: PhrankenPhilco 610-630 - by kc5gym - 08-07-2016, 08:02 PM
RE: PhrankenPhilco 610-630 - by Radioroslyn - 08-07-2016, 08:51 PM
RE: PhrankenPhilco 610-630 - by kc5gym - 08-08-2016, 05:33 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM
38-10T chassis Restoration begins
I have a question about the mica sheets. I thought I saw somewhere on the Phorum where someone used thin plastic report ...dconant — 10:44 AM
38-10T chassis Restoration begins
Yes, you should carefully remove the mica sheets from the trimmers otherwise you risk trapping foreign material in the t...RodB — 10:34 AM

[-]
Who's Online
There are currently 2856 online users. [Complete List]
» 1 Member(s) | 2855 Guest(s)
Avatar

>