Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith 10-H-571 "Spinet"
#80

Thanks John, thanks everyone.


Tonight I used my "time off" to open and clean the volume control and the power switch. The switch was working but was a bit dirty.
Volume had lapses and scratching.
I opened it, no small doing, the resistor has 6 lugs, and the face plate on one side had the tabs soldered to it. The resistor itself is cylindrical, not flat, and very, very narrow.
As usual, Deoxit spay, then a little dab of Deoxit/Lithium grease. Now it is quiet and seems to have no lapses.


Question: who knows what belt should there be to drive the pulley that drives the tunng cap from the knurled cylinder attached to the flywheel? I have a rope with ends tied together as a large nod. It is loose. I wonder if it s original or should there be a belt?

KCMike, could you possibly look in yours?

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
Zenith 10-H-571 "Spinet" - by morzh - 01-07-2017, 07:54 PM
RE: Zenith 10-H-571 "Spinet" - by sam - 01-07-2017, 07:58 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-07-2017, 08:18 PM
RE: Zenith 10-H-571 "Spinet" - by KCMike - 01-07-2017, 08:47 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-07-2017, 09:34 PM
RE: Zenith 10-H-571 "Spinet" - by Paul Philco322 - 01-07-2017, 10:30 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-07-2017, 10:55 PM
RE: Zenith 10-H-571 "Spinet" - by Jayce - 01-08-2017, 12:14 AM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-08-2017, 12:27 AM
RE: Zenith 10-H-571 "Spinet" - by Jayce - 01-08-2017, 01:14 AM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-08-2017, 10:53 AM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-08-2017, 08:55 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-08-2017, 09:34 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-08-2017, 09:54 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-08-2017, 09:55 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-08-2017, 10:34 PM
RE: Zenith 10-H-571 "Spinet" - by Jayce - 01-08-2017, 11:22 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-08-2017, 11:35 PM
RE: Zenith 10-H-571 "Spinet" - by Arran - 01-09-2017, 05:23 AM
RE: Zenith 10-H-571 "Spinet" - by KCMike - 01-08-2017, 11:48 PM
RE: Zenith 10-H-571 "Spinet" - by Jayce - 01-09-2017, 01:36 AM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-09-2017, 09:37 AM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-10-2017, 10:04 AM
RE: Zenith 10-H-571 "Spinet" - by Arran - 01-13-2017, 01:12 AM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-11-2017, 12:13 AM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-11-2017, 04:28 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-12-2017, 11:24 AM
RE: Zenith 10-H-571 "Spinet" - by Eliot Ness - 01-12-2017, 12:58 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-12-2017, 06:06 PM
RE: Zenith 10-H-571 "Spinet" - by TV MAN - 01-12-2017, 06:58 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-12-2017, 11:20 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-13-2017, 10:22 AM
RE: Zenith 10-H-571 "Spinet" - by Arran - 01-14-2017, 03:45 AM
RE: Zenith 10-H-571 "Spinet" - by Phlogiston - 01-13-2017, 12:18 PM
RE: Zenith 10-H-571 "Spinet" - by Mondial - 01-14-2017, 01:47 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-14-2017, 08:15 PM
RE: Zenith 10-H-571 "Spinet" - by Paul Philco322 - 01-14-2017, 10:11 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-14-2017, 10:46 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-23-2017, 10:04 AM
RE: Zenith 10-H-571 "Spinet" - by Eliot Ness - 01-23-2017, 10:59 AM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-23-2017, 11:12 AM
RE: Zenith 10-H-571 "Spinet" - by Eliot Ness - 01-23-2017, 08:54 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-23-2017, 10:01 PM
RE: Zenith 10-H-571 "Spinet" - by Phlogiston - 01-26-2017, 01:30 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-26-2017, 03:14 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 01-27-2017, 07:14 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 02-11-2017, 10:43 PM
RE: Zenith 10-H-571 "Spinet" - by Mondial - 02-12-2017, 03:15 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 02-12-2017, 09:22 PM
RE: Zenith 10-H-571 "Spinet" - by KCMike - 02-12-2017, 09:48 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 02-12-2017, 10:30 PM
RE: Zenith 10-H-571 "Spinet" - by KCMike - 02-12-2017, 11:00 PM
RE: Zenith 10-H-571 "Spinet" - by KCMike - 02-24-2017, 01:16 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 02-24-2017, 02:27 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 02-26-2017, 11:39 PM
RE: Zenith 10-H-571 "Spinet" - by Eliot Ness - 02-27-2017, 12:43 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 02-27-2017, 01:30 PM
RE: Zenith 10-H-571 "Spinet" - by Eliot Ness - 02-27-2017, 03:02 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 02-27-2017, 03:39 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 02-27-2017, 05:19 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-06-2017, 12:28 AM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-11-2017, 05:04 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-11-2017, 05:30 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-11-2017, 06:23 PM
RE: Zenith 10-H-571 "Spinet" - by KCMike - 03-11-2017, 10:54 PM
RE: Zenith 10-H-571 "Spinet" - by klondike98 - 03-11-2017, 11:02 PM
RE: Zenith 10-H-571 "Spinet" - by OldRestorer - 03-12-2017, 07:39 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-12-2017, 08:41 PM
RE: Zenith 10-H-571 "Spinet" - by OldRestorer - 03-12-2017, 09:04 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-12-2017, 11:03 PM
RE: Zenith 10-H-571 "Spinet" - by Arran - 03-13-2017, 12:26 AM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-13-2017, 10:30 AM
RE: Zenith 10-H-571 "Spinet" - by Eliot Ness - 03-14-2017, 11:59 AM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-14-2017, 06:57 PM
RE: Zenith 10-H-571 "Spinet" - by KCMike - 03-14-2017, 08:29 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-14-2017, 08:36 PM
RE: Zenith 10-H-571 "Spinet" - by Eliot Ness - 03-14-2017, 08:42 PM
RE: Zenith 10-H-571 "Spinet" - by KCMike - 03-14-2017, 08:46 PM
RE: Zenith 10-H-571 "Spinet" - by Eliot Ness - 03-14-2017, 08:56 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-14-2017, 09:45 PM
RE: Zenith 10-H-571 "Spinet" - by KCMike - 03-14-2017, 10:40 PM
RE: Zenith 10-H-571 "Spinet" - by OldRestorer - 03-15-2017, 08:04 AM
RE: Zenith 10-H-571 "Spinet" - by Eliot Ness - 03-15-2017, 12:02 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-15-2017, 08:16 AM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-15-2017, 07:43 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-19-2017, 09:53 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-20-2017, 11:11 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-25-2017, 05:57 PM
RE: Zenith 10-H-571 "Spinet" - by Arran - 03-26-2017, 10:46 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-25-2017, 07:21 PM
RE: Zenith 10-H-571 "Spinet" - by KCMike - 03-25-2017, 09:31 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-25-2017, 09:44 PM
RE: Zenith 10-H-571 "Spinet" - by KCMike - 03-25-2017, 10:28 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-26-2017, 01:51 PM
RE: Zenith 10-H-571 "Spinet" - by KCMike - 03-26-2017, 07:50 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-26-2017, 08:57 PM
RE: Zenith 10-H-571 "Spinet" - by KCMike - 03-26-2017, 10:06 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-26-2017, 10:15 PM
RE: Zenith 10-H-571 "Spinet" - by morzh - 03-26-2017, 11:14 PM



Users browsing this thread: 17 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

[-]
Who's Online
There are currently 5803 online users. [Complete List]
» 1 Member(s) | 5802 Guest(s)
Avatar

>