bakelite block question

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

bakelite block question

murf
Senior Member

Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.

04-10-2017, 05:29 PM

Working on a 38-116 code 125 and have a question concerning bakelite blk. number 46.
This is a 4989SG which is listed on the parts list as having a single .1 uf cap.
If you look on the handy reference guide that I printed out from the Philco site, it does not list a 4989SG.
Anyone know what the proper wiring would be as far as the new .1 cap.
Lugs 1 to 2 or lugs 1 to 3 ?
Thanks,
murf

Find

« Next Oldest | Next Newest »

Messages In This Thread

bakelite block question - by murf - 04-10-2017, 05:29 PM

RE: bakelite block question - by doc612 - 04-10-2017, 06:22 PM

RE: bakelite block question - by murf - 04-10-2017, 06:46 PM

RE: bakelite block question - by murf - 04-10-2017, 07:38 PM

RE: bakelite block question - by doc612 - 04-10-2017, 07:55 PM

RE: bakelite block question - by Steve Davis - 04-10-2017, 08:54 PM

RE: bakelite block question - by murf - 04-10-2017, 09:36 PM

RE: bakelite block question - by doc612 - 04-10-2017, 09:01 PM

RE: bakelite block question - by murf - 04-10-2017, 09:26 PM

RE: bakelite block question - by Radioroslyn - 04-10-2017, 09:44 PM

RE: bakelite block question - by murf - 04-10-2017, 10:07 PM

RE: bakelite block question - by Warren - 04-10-2017, 10:29 PM

RE: bakelite block question - by Radioroslyn - 04-10-2017, 10:39 PM

RE: bakelite block question - by murf - 04-11-2017, 06:44 PM

RE: bakelite block question - by Radioroslyn - 04-11-2017, 07:49 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This sho...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A5...MrFixr55 — 06:48 AM

Who's Online

There are currently 4208 online users. [Complete List]
» 3 Member(s) | 4205 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me