Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Help ID this floor model
#7

        Hi all, Well this radio finally made its way from MA to my bench in PA. The friend of mine was visiting his daughter and brought it home with him. I have some pics attached above. So, in all this time I haven't found much about this rare bird. It appears to be a Radiotrope #1016 or 1010, the label is a little fuzzy. Looks to be an early 30s superhet. There's no tube placement chart in it, but it has 10 tubes as follows:....
4- #27
 3- #35
 2- #47
 1- #80
It also has a tuning or signal strength meter. I would appreciate any info on this and also need a schematic. Thanks

Ron

Bendix 0626.      RCA 8BX5.   RCA T64
Philco 41-250.    Philco49-500
GE 201.             Philco 39-25
Motorola 61X13. Philco 46-42        Crosley 52TQ
Philco 37-116.    Philco 70
AK 35                Philco 46-350
Philco 620B.       Zenith Transoceanic B-600
Philco 60B.         Majestic 50
Philco 52-944.    AK 84


Messages In This Thread
Help ID this floor model - by 462ron - 08-24-2017, 08:08 PM
RE: Help ID this floor model - by Jayce - 08-25-2017, 12:21 AM
RE: Help ID this floor model - by 462ron - 08-25-2017, 02:10 PM
RE: Help ID this floor model - by morzh - 08-25-2017, 04:38 PM
RE: Help ID this floor model - by Eliot Ness - 08-25-2017, 05:06 PM
RE: Help ID this floor model - by 462ron - 08-25-2017, 05:41 PM
RE: Help ID this floor model - by 462ron - 04-23-2018, 03:30 PM
RE: Help ID this floor model - by palegreenthumb - 04-23-2018, 11:34 PM
RE: Help ID this floor model - by 462ron - 04-24-2018, 08:07 AM
RE: Help ID this floor model - by Eliot Ness - 04-24-2018, 09:18 AM
RE: Help ID this floor model - by 462ron - 04-24-2018, 04:22 PM
RE: Help ID this floor model - by 462ron - 04-30-2018, 07:21 PM
RE: Help ID this floor model - by Arran - 05-01-2018, 12:29 AM
RE: Help ID this floor model - by 462ron - 06-07-2018, 02:58 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5100 online users. [Complete List]
» 2 Member(s) | 5098 Guest(s)
AvatarAvatar

>