1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Where to find eyelets and tool(s)?
EdHolland
Phorum Expert
*****
Posts: 1,287
Threads: 44
Joined: Nov 2017
City: Menlo Park State, Province, Country: CA
#31

04-25-2018, 08:02 PM
I Just had another thought about this...

Hollow grommets & rivets are available in brass, the issue is setting them in place on a chassis. It just occurred to me that one could use a pop rivet tool, if a suitable substitute is used for the shear pin. This could be a nail etc of the appropriate length and diameter.

As I said, just a thought.
I don't hold with furniture that talks.
Find
« Next Oldest | Next Newest »


Messages In This Thread
RE: Where to find eyelets and tool(s)? - by w4rtc - 04-09-2018, 10:49 AM
RE: Where to find eyelets and tool(s)? - by gregb - 04-09-2018, 11:14 AM
RE: Where to find eyelets and tool(s)? - by morzh - 04-09-2018, 01:20 PM
RE: Where to find eyelets and tool(s)? - by Arran - 04-10-2018, 12:11 AM
RE: Where to find eyelets and tool(s)? - by morzh - 04-10-2018, 04:37 PM
RE: Where to find eyelets and tool(s)? - by morzh - 04-12-2018, 08:45 PM
RE: Where to find eyelets and tool(s)? - by EdHolland - 04-25-2018, 08:02 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration