Thoughts on finish

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Thoughts on finish

tbone
Senior Member

Posts: 279
Threads: 19
Joined: Nov 2016
City: Cromwell State, Province, Country: CT

#16

06-07-2018, 06:47 AM

Nice radio John!
You are right about nice original finish. I think some of us have better luck at finding these radios than others. The way the cookie crumbles as they say.

Tony

“People may not remember how fast you did a job, but they will remember how well you did it”

Find

« Next Oldest | Next Newest »

Messages In This Thread

Thoughts on finish - by oscartg - 06-06-2018, 11:54 AM

RE: Thoughts on finish - by Ron Ramirez - 06-06-2018, 12:35 PM

RE: Thoughts on finish - by oscartg - 06-06-2018, 12:40 PM

RE: Thoughts on finish - by John Bartley - 06-06-2018, 12:43 PM

RE: Thoughts on finish - by oscartg - 06-06-2018, 12:47 PM

RE: Thoughts on finish - by Ron Ramirez - 06-06-2018, 12:57 PM

RE: Thoughts on finish - by oscartg - 06-06-2018, 01:08 PM

RE: Thoughts on finish - by oscartg - 06-06-2018, 01:26 PM

RE: Thoughts on finish - by Ron Ramirez - 06-06-2018, 02:20 PM

RE: Thoughts on finish - by oscartg - 06-06-2018, 02:28 PM

RE: Thoughts on finish - by Ron Ramirez - 06-06-2018, 02:30 PM

RE: Thoughts on finish - by EdHolland - 06-06-2018, 04:01 PM

RE: Thoughts on finish - by Arran - 06-07-2018, 12:32 AM

RE: Thoughts on finish - by tbone - 06-07-2018, 06:20 AM

RE: Thoughts on finish - by John Bartley - 06-07-2018, 06:41 AM

RE: Thoughts on finish - by tbone - 06-07-2018, 06:47 AM

RE: Thoughts on finish - by EdHolland - 06-07-2018, 12:58 PM

RE: Thoughts on finish - by rdnzl - 06-07-2018, 01:21 PM

RE: Thoughts on finish - by Nathan Slingerland - 06-07-2018, 01:28 PM

RE: Thoughts on finish - by Phlogiston - 06-07-2018, 04:23 PM

RE: Thoughts on finish - by Arran - 06-07-2018, 10:00 PM

RE: Thoughts on finish - by oscartg - 06-12-2018, 11:12 AM

RE: Thoughts on finish - by Phlogiston - 06-12-2018, 02:53 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

Who's Online

There are currently 4587 online users. [Complete List]
» 2 Member(s) | 4585 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me