1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Label set for Philco 70
Retroguy55
Junior Member
**
Posts: 14
Threads: 2
Joined: Jul 2019
City: Boca Raton State, Province, Country: Florida
#1

07-08-2020, 12:00 PM
Does anyone currently make a label set for the Philco Model 70?

I understand the ones sold on Ebay a few years back were not very good.

I saw a old post about Chuck Paci making these but when I sent an email to cpaci1@verizon.net it came back as undeliverable.

Has anyone found a source currently producing these?

Thanks,

Ron
Find
« Next Oldest | Next Newest »


Messages In This Thread
Label set for Philco 70 - by Retroguy55 - 07-08-2020, 12:00 PM
RE: Label set for Philco 70 - by Retroguy55 - 07-08-2020, 01:42 PM
RE: Label set for Philco 70 - by morzh - 07-08-2020, 08:12 PM
RE: Label set for Philco 70 - by Retroguy55 - 07-09-2020, 11:29 AM
RE: Label set for Philco 70 - by Retroguy55 - 07-10-2020, 02:40 PM
RE: Label set for Philco 70 - by Retroguy55 - 07-10-2020, 03:04 PM
RE: Label set for Philco 70 - by Retroguy55 - 07-10-2020, 06:22 PM
RE: Label set for Philco 70 - by Retroguy55 - 07-10-2020, 06:23 PM
RE: Label set for Philco 70 - by Retroguy55 - 07-10-2020, 06:54 PM
RE: Label set for Philco 70 - by Retroguy55 - 07-26-2020, 07:29 PM
RE: Label set for Philco 70 - by Retroguy55 - 08-05-2020, 04:39 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration