1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Label set for Philco 70
Nathan Slingerland
Super Moderator
******
Posts: 1,874
Threads: 212
Joined: May 2015
City: Seattle State, Province, Country: WA
#13

07-10-2020, 06:50 PM
Thanks Ron!

For some reason the scan was at pretty low resolution. Generally scanner software will let you preview then select just a small area that you can scan at higher resolution.

The new photo is better. I'll give it a try with that.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Label set for Philco 70 - by Retroguy55 - 07-08-2020, 12:00 PM
RE: Label set for Philco 70 - by Retroguy55 - 07-08-2020, 01:42 PM
RE: Label set for Philco 70 - by morzh - 07-08-2020, 08:12 PM
RE: Label set for Philco 70 - by Retroguy55 - 07-09-2020, 11:29 AM
RE: Label set for Philco 70 - by Retroguy55 - 07-10-2020, 02:40 PM
RE: Label set for Philco 70 - by Retroguy55 - 07-10-2020, 03:04 PM
RE: Label set for Philco 70 - by Retroguy55 - 07-10-2020, 06:22 PM
RE: Label set for Philco 70 - by Retroguy55 - 07-10-2020, 06:23 PM
RE: Label set for Philco 70 - by Nathan Slingerland - 07-10-2020, 06:50 PM
RE: Label set for Philco 70 - by Retroguy55 - 07-10-2020, 06:54 PM
RE: Label set for Philco 70 - by Retroguy55 - 07-26-2020, 07:29 PM
RE: Label set for Philco 70 - by Retroguy55 - 08-05-2020, 04:39 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 4000 online users. [Complete List]
» 3 Member(s) | 3997 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration