Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

Philco 38-10
#9

On the outside antenna, when I first turn on the set I receive stations fine all up and down the broadcast band. WSM comes in strong at 650 as it should, but, after a little while the lower end of the band fades away. The upper end from about 1000KC on still comes in quite strong, with lots of stations, but below that reception faces quickly, and below about 800Kc the radio becomes deaf as a post. I pulled the chassis again, and rechecked the alignment over and over. I did notice it is still flukey even just trying to align it. I am going to replace some tubes because I am wondering if I have one that is going weak as it heats. Oddly, short wave seems much less affected than the broadcast band. I have checked and rechecked the connections, and I don't think they are the problem. If any of you have encountered the same sort of problem let me know, and tell me if you discovered the cause.


Messages In This Thread
Philco 38-10 - by mikethedruid - 03-21-2021, 10:16 PM
RE: Philco 38-10 - by mikethedruid - 03-22-2021, 05:29 PM
RE: Philco 38-10 - by David - 03-22-2021, 08:51 PM
RE: Philco 38-10 - by mikethedruid - 03-22-2021, 09:58 PM
RE: Philco 38-10 - by mikethedruid - 03-23-2021, 08:35 PM
RE: Philco 38-10 - by Ron Ramirez - 03-23-2021, 10:05 PM
RE: Philco 38-10 - by mikethedruid - 03-24-2021, 12:00 PM
RE: Philco 38-10 - by mikethedruid - 03-25-2021, 02:58 PM
RE: Philco 38-10 - by mikethedruid - 03-25-2021, 09:48 PM
RE: Philco 38-10 - by mikethedruid - 03-26-2021, 01:59 AM
RE: Philco 38-10 - by RodB - 03-26-2021, 09:32 AM
RE: Philco 38-10 - by mikethedruid - 03-26-2021, 03:00 PM
RE: Philco 38-10 - by mikethedruid - 03-27-2021, 08:57 PM
RE: Philco 38-10 - by mikethedruid - 03-29-2021, 07:11 PM
RE: Philco 38-10 - by mikethedruid - 03-30-2021, 07:40 PM
RE: Philco 38-10 - by mikethedruid - 04-05-2021, 03:03 PM
RE: Philco 38-10 - by mikethedruid - 04-05-2021, 09:27 PM
RE: Philco 38-10 - by radiorich - 10-25-2021, 06:22 PM
RE: Philco 38-10 - by Brad Winder - 10-31-2021, 01:38 PM
RE: Philco 38-10 - by David - 10-31-2021, 04:33 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
54C Complete Teardown/Rebuild
Hello Roy, here is this one sincerely Richardradiorich — 12:45 AM
54C Complete Teardown/Rebuild
Richard, Had grabbed it already but thank you just the same.  I find myself wanting to find some way to block out the...glyphmon — 12:03 AM
54C Complete Teardown/Rebuild
Hello roy, here is a link to the schematic . Sincerely Richardradiorich — 11:54 PM
54C Complete Teardown/Rebuild
Richard, The Silvertone 2014 also is a transformerless set, so I am incorporating a 1:1 600 ohm audio isolation transfo...glyphmon — 11:37 PM
Preliminary work on wife's Silvertone 2014
Did an alignment today which was interesting.  IF alignment went great, almost all was already spot-on.  Adjusting on th...glyphmon — 11:35 PM
54C Complete Teardown/Rebuild
The main problem with adding a Bluetooth input is that this set lacks a traditional power transformer to isolate it from...radiorich — 11:19 PM
54C Cabinet Refinish
I started stripping this cabinet before it got super chilly out because I knew I wasn't going to be able to work on ...glyphmon — 11:18 PM
54C Complete Teardown/Rebuild
While I'm waiting to wrap up the final steps on my wife's Silvertone 2014, I started disassembly on the next project.  O...glyphmon — 11:07 PM
Preliminary work on wife's Silvertone 2014
Hello roy, that great news glad it worked out for you !! Sincerely Richardradiorich — 10:50 PM
Preliminary work on wife's Silvertone 2014
Safety caps arrived today.  Soldered one in and had a successful first power-up.  No magic smoke escaped and it tunes in...glyphmon — 09:53 PM

[-]
Who's Online
There are currently no members online.

>