Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 70 Cathedral
#21

Ron Ramirez is right. You don't want that primary wound on top of the secondary. Reason is that the coil is designed for nominal coupling across the band. If you were to wind it on top, you may get better coupling in the lower part of the band, but you would lose total Q in the circuit and also change how it tracks across the band...


Messages In This Thread
Philco 70 Cathedral - by 462ron - 02-10-2021, 03:46 PM
RE: Philco 70 Cathedral - by Radioroslyn - 02-10-2021, 04:17 PM
RE: Philco 70 Cathedral - by 462ron - 02-11-2021, 12:12 AM
RE: Philco 70 Cathedral - by 462ron - 02-24-2021, 03:56 PM
RE: Philco 70 Cathedral - by patrician56 - 02-24-2021, 05:48 PM
RE: Philco 70 Cathedral - by patrician56 - 02-24-2021, 05:50 PM
RE: Philco 70 Cathedral - by Radioroslyn - 02-24-2021, 08:34 PM
RE: Philco 70 Cathedral - by 462ron - 02-25-2021, 08:16 AM
RE: Philco 70 Cathedral - by Radioroslyn - 02-25-2021, 09:56 AM
RE: Philco 70 Cathedral - by 462ron - 02-25-2021, 10:05 AM
RE: Philco 70 Cathedral - by Steve Davis - 02-25-2021, 10:22 AM
RE: Philco 70 Cathedral - by 462ron - 02-25-2021, 12:10 PM
RE: Philco 70 Cathedral - by 462ron - 04-12-2021, 02:49 PM
RE: Philco 70 Cathedral - by rfeenstra - 04-12-2021, 04:38 PM
RE: Philco 70 Cathedral - by 462ron - 04-12-2021, 06:15 PM
RE: Philco 70 Cathedral - by 462ron - 05-25-2021, 04:26 PM
RE: Philco 70 Cathedral - by Paul Philco322 - 05-25-2021, 05:03 PM
RE: Philco 70 Cathedral - by Ron Ramirez - 05-25-2021, 05:06 PM
RE: Philco 70 Cathedral - by 462ron - 05-25-2021, 06:11 PM
RE: Philco 70 Cathedral - by Ron Ramirez - 05-25-2021, 11:00 PM
RE: Philco 70 Cathedral - by BrendaAnnD - 05-26-2021, 02:19 AM
RE: Philco 70 Cathedral - by 462ron - 05-26-2021, 07:55 AM
RE: Philco 70 Cathedral - by Radioroslyn - 05-26-2021, 08:26 AM
RE: Philco 70 Cathedral - by Radioroslyn - 05-26-2021, 10:10 AM
RE: Philco 70 Cathedral - by 462ron - 05-26-2021, 12:31 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

[-]
Who's Online
There are currently 3669 online users. [Complete List]
» 2 Member(s) | 3667 Guest(s)
AvatarAvatar

>