1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Westinghouse H-104A - Low Volume
Masonparker
Junior Member
**
Posts: 47
Threads: 10
Joined: Nov 2020
City: CHESAPEAKE State, Province, Country: VA
#1

01-02-2022, 12:17 PM
Working on a H-104A did the usual recap and checked all the resistors.  The radio has good reception but the volume is low.   I checked and rechecked all the new connections all look good in that nothing is touching it shouldn't.  I checked the voltages ( see attached) The plate voltage on 6SK7 is high.  Also the voltage on the 6AT6 which was changed per the attached supplement has two pins that have high voltage.


Attached Files
.pdf Scan_0059.pdf Size: 616.36 KB  Downloads: 191
.pdf Scan_0060.pdf Size: 408.67 KB  Downloads: 157
.pdf Scan_0061.pdf Size: 372.38 KB  Downloads: 184
Find
« Next Oldest | Next Newest »


Messages In This Thread
Westinghouse H-104A - Low Volume - by Masonparker - 01-02-2022, 12:17 PM
RE: Westinghouse H-104A - Low Volume - by Mondial - 01-02-2022, 01:13 PM
RE: Westinghouse H-104A - Low Volume - by Mondial - 01-02-2022, 07:33 PM
RE: Westinghouse H-104A - Low Volume - by Mondial - 01-03-2022, 09:54 PM
RE: Westinghouse H-104A - Low Volume - by Mondial - 01-04-2022, 10:52 PM
RE: Westinghouse H-104A - Low Volume - by David - 01-08-2022, 04:40 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together. As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM
37-690 Bass Choke Replacement
This is the parts catalog. 32-7528 choke is 65H, 10mA, 2,250 Ohm inductance. Find a suitable one.morzh — 02:18 PM
37-690 Bass Choke Replacement
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM

[-]
Who's Online
There are currently 3829 online users. [Complete List]
» 1 Member(s) | 3828 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)