Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 86 Voltages
#2

Hi Tiddat,

Welcome to te Phorum!

The 80 is likely OK. The voltages are high due to a low current draw. These power supplies always run higher when there is no "load" connected to it. Therefore, the issue is that there are circuits that are not drawing what they should.

http://www.nostalgiaair.org/PagesByModel...029653.pdf

According to the above schematic, there should be about 160V on the plates of the 71A Output tubes. If that value is high, the 71As may be bad, and may be the reason for the low volume. I fixed a Gloritone several years ago for a friend with the same symptoms. Audio output was a single '45 tube. When replaced, issue was solved. Radio played loud and proud and B+ voltages returned to normal.

This radio needs a rather long antenna. This is a "TRF" set, very similar to Atwater Kent and RCA TRF sets of the period, except that this et has a Push Pull output which gives superior, lower distortion sound. Unfortunately, the grid leak detector used in this set gives higher distortion than a diode detector. This set may also employ the "Neutrodyne" circuit, and unlike the Radiola 16, 17, 18 and the A-K 5, 40, 35c, the first RF stage is tuned.

This set does have a built in "local" antenna (Capacitive coupling to AC Line. However, ensure that the capacitor 33 is new and of a "Safety" type.

"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
"Let us begin to do good"- St. Francis

Best Regards, 

MrFixr55


Messages In This Thread
Philco 86 Voltages - by Tiddat33 - 02-06-2023, 12:13 AM
RE: Philco 86 Voltages - by MrFixr55 - 02-06-2023, 08:52 AM
RE: Philco 86 Voltages - by Tiddat33 - 02-06-2023, 10:44 PM
RE: Philco 86 Voltages - by MrFixr55 - 02-06-2023, 10:58 PM
RE: Philco 86 Voltages - by RodB - 02-07-2023, 10:32 AM
RE: Philco 86 Voltages - by Ron Ramirez - 02-07-2023, 01:53 PM
RE: Philco 86 Voltages - by RodB - 02-07-2023, 02:46 PM
RE: Philco 86 Voltages - by Tiddat33 - 02-07-2023, 09:07 PM
RE: Philco 86 Voltages - by Radioroslyn - 02-08-2023, 01:15 PM
RE: Philco 86 Voltages - by MrFixr55 - 02-08-2023, 03:51 PM
RE: Philco 86 Voltages - by Ron Ramirez - 02-08-2023, 03:56 PM
RE: Philco 86 Voltages - by RodB - 02-08-2023, 04:06 PM
RE: Philco 86 Voltages - by Arran - 02-08-2023, 04:08 PM
RE: Philco 86 Voltages - by Tiddat33 - 02-08-2023, 09:58 PM
RE: Philco 86 Voltages - by Radioroslyn - 02-08-2023, 10:52 PM
RE: Philco 86 Voltages - by radiorich - 02-09-2023, 09:31 AM
RE: Philco 86 Voltages - by Tiddat33 - 02-12-2023, 06:50 PM
RE: Philco 86 Voltages - by RodB - 02-13-2023, 10:37 AM
RE: Philco 86 Voltages - by Tiddat33 - 02-13-2023, 05:10 PM
RE: Philco 86 Voltages - by Ron Ramirez - 02-13-2023, 08:42 PM
RE: Philco 86 Voltages - by RodB - 02-13-2023, 09:03 PM
RE: Philco 86 Voltages - by Ron Ramirez - 02-14-2023, 09:19 AM
RE: Philco 86 Voltages - by Arran - 02-14-2023, 02:20 PM
RE: Philco 86 Voltages - by Ron Ramirez - 02-14-2023, 02:29 PM
RE: Philco 86 Voltages - by RodB - 02-14-2023, 02:29 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM
My Philco 37-116 Restore
Are you measuring relative to the centertap or the GND?morzh — 11:57 PM
Philco 610B oscillator wiring
Still not clear on the wiring interface between the 6A7 and oscillator. After refering to the available schematics and s...Tubester — 07:18 PM
Refinishing Ideas
My 37-116 code 121 is the best sounding radio i have...a daily driver. Since we are talking about "changes". ...poulsbobill — 07:18 PM
My Philco 37-116 Restore
Hello, I finally got brave enough to take the cans off the Expander Unit. Got the grid cap wires replaced and back toget...dconant — 06:50 PM
Zenith H725
I got into the first AM IF can today, and found its mica was cracked. Amazing that it was still working. This one makes ...EdHolland — 06:10 PM
Philco model #20
AHH HA , I got it and can’t thank you fellows enough , when I changed the capacitors I took the advice and did not unsol...onlyrick — 02:24 PM
Zenith H725
Hello Ed, yes, I like letting projects run for few days to make sure they don't start acting up . Sincerely Richardradiorich — 01:03 PM
Philco 46-480 Electronic Restoration
I am almost finished with this restoration. All which remains is the power transformer. I cleaned it up some time ago, b...jrblasde — 12:41 PM
Philco model #20
I seem to recall in some TRF sets there being a Local/Distance toggle switch that removes the B+ from the first 24 rf tu...RodB — 09:46 AM

[-]
Who's Online
There are currently no members online.

>