39-6443E

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

39-6443E

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#11

11-30-2023, 09:29 AM

The 84/6Z4 is a 5 pin job. Do note that the 5Y3 and 5Y4 are not interchangeable because the filament and plate pin are wired differently. Philco sets that have the original socket for the rectifier some of the reciprocals for the pins are deleted. This means if you happen to have a 5Y3 and not a 5Y4 you can't add a few jumpers so both tubes could be used. Those sneak! This doesn't apply to this set as the socket is a replacement.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

(This post was last modified: 11-30-2023, 09:51 AM by Radioroslyn.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

39-6443E - by Paulroney - 11-23-2023, 02:27 PM

RE: 39-6443E - by patrician56 - 11-23-2023, 04:00 PM

462ron - by 462ron - 11-24-2023, 08:35 AM

RE: 39-6443E - by Paulroney - 11-24-2023, 09:02 AM

RE: 39-6443E - by madsowry - 11-24-2023, 01:00 PM

RE: 39-6443E - by Brad Winder - 11-27-2023, 11:34 PM

RE: 39-6443E - by patrician56 - 11-28-2023, 04:56 PM

RE: 39-6443E - by Joe Rossi - 11-29-2023, 11:14 PM

RE: 39-6443E - by Paulroney - 11-30-2023, 12:57 AM

RE: 39-6443E - by Arran - 11-30-2023, 02:41 AM

RE: 39-6443E - by Radioroslyn - 11-30-2023, 09:29 AM

RE: 39-6443E - by Joe Rossi - 11-30-2023, 02:12 PM

RE: 39-6443E - by Radioroslyn - 11-30-2023, 05:44 PM

RE: 39-6443E - by David - 11-30-2023, 07:50 PM

RE: 39-6443E - by Joe Rossi - 11-30-2023, 09:39 PM

RE: 39-6443E - by Arran - 12-01-2023, 03:07 AM

RE: 39-6443E - by Joe Rossi - 12-01-2023, 08:23 AM

RE: 39-6443E - by David - 12-01-2023, 08:28 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit. That would rem...alangard — 09:30 PM
HiFi (Chifi) tube amp build - but my own design.
Tim Well...a chassis is metal. Magnetic or not, it does not matter. A transformer has some hum to it. It is natural....morzh — 08:40 PM
Hickok AC51 tube tester
I thought the 83 tube was bad because it looked white but it tests strong. Blue gassy though. I checked the fuse, it was...martinj — 08:37 PM
Shadow Meter Bulb
Ross I am not sure what current limiting effect the incandescent provides. They are two different parts of the sch...morzh — 08:31 PM
12' Philco
Bob Thanks for that photo. I have been looking for it, and I cannot find anythinmg on the web. I forgot it was here...morzh — 08:29 PM
Shadow Meter Bulb
I think after all has been said, I will use the same bulb that is specified for the dial pilot light which is a #55. I ...georgetownjohn — 07:31 PM
12' Philco
There was also this Philco! klondike98 — 07:25 PM
HiFi (Chifi) tube amp build - but my own design.
I expected a challenge and this is just part of it. But, it's also supposed to be fun, entertaining, informative and enj...TV MAN — 07:12 PM
Shadow Meter Bulb
Butting in here with a question. Since the shadow meter is connected directly to the 1st and 2nd I.F.'s wouldn't the met...RossH — 06:43 PM
HiFi (Chifi) tube amp build - but my own design.
Mike, Tim; you are about to enter the twilight zone. Doo doo doo doo, doo doo doo doo This is something alright. I'm go...RodB — 06:26 PM

Who's Online

There are currently 5259 online users. [Complete List]
» 1 Member(s) | 5258 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me