Hallicrafters SX-62

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Hallicrafters SX-62

bridkarl
Member

Posts: 182
Threads: 39
Joined: May 2023
City: Pocatello State, Province, Country: idaho

#13

05-04-2024, 10:01 PM

Thanks. In this case the terminals just broke off even with the base of the socket. No saving it. Plus these were so dirty, greasy and filled with old solder just better to start clean

Find

« Next Oldest | Next Newest »

Messages In This Thread

Hallicrafters SX-62 - by bridkarl - 03-29-2024, 09:56 PM

RE: Hallicrafters SX-62 - by Arran - 03-30-2024, 12:38 AM

RE: Hallicrafters SX-62 - by bridkarl - 03-30-2024, 07:48 AM

RE: Hallicrafters SX-62 - by RodB - 03-30-2024, 08:56 AM

RE: Hallicrafters SX-62 - by bridkarl - 03-30-2024, 10:36 AM

RE: Hallicrafters SX-62 - by David - 03-30-2024, 03:06 PM

RE: Hallicrafters SX-62 - by bridkarl - 03-30-2024, 03:21 PM

bridkarl - by bridkarl - 04-01-2024, 11:10 PM

RE: Hallicrafters SX-62 - by bridkarl - 05-03-2024, 09:29 PM

RE: Hallicrafters SX-62 - by RodB - 05-03-2024, 10:48 PM

RE: Hallicrafters SX-62 - by bridkarl - 05-04-2024, 12:00 PM

RE: Hallicrafters SX-62 - by Arran - 05-04-2024, 09:53 PM

RE: Hallicrafters SX-62 - by bridkarl - 05-04-2024, 10:01 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM
Looking for verification of correct schematic.
Klondike98, Thank you. I'll double check that SN and get back to you. GarySP, Thank you for the schematic.RossH — 12:13 AM
Looking for verification of correct schematic.
I think you have the correct take on your set. Ron's annotated early schematics that note the below B22000 serial numbe...klondike98 — 12:04 AM
Looking for verification of correct schematic.
Hello Ross. The Philco Radio Library located at the bottom of the page has the schematic with the tube count you have. ...GarySP — 10:48 PM

Who's Online

There are currently 1468 online users. [Complete List]
» 1 Member(s) | 1467 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me