Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 96 cabinet veneer
#5

You are probably skipping the final step. Once you select the photos you want and they get downloaded, the system assigns a serial number to each one and displays a list to you. You can then select the photos and scroll back to your text and put the cursor where you want the photo. Then scroll back down and click on Insert In Text. Then open a container of your favorite beverage and enjoy.


Messages In This Thread
Model 96 cabinet veneer - by TGLager - 10-23-2024, 04:48 PM
RE: Model 96 cabinet veneer - by Arran - 10-23-2024, 11:08 PM
RE: Model 96 cabinet veneer - by klondike98 - 11-04-2024, 12:59 AM
RE: Model 96 cabinet veneer - by TGLager - 11-09-2024, 04:08 PM
RE: Model 96 cabinet veneer - by RodB - 11-10-2024, 10:36 AM
RE: Model 96 cabinet veneer - by TGLager - 11-10-2024, 02:40 PM
RE: Model 96 cabinet veneer - by RodB - 11-10-2024, 07:01 PM
RE: Model 96 cabinet veneer - by TGLager - 11-10-2024, 11:02 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
[split] Newbie questions RE: Philco 41-608
I agree with Morzh. I've split this issue to it's own thread. Take care and BE HEALTHY! GaryGarySP — 09:03 PM
Newbie questions RE: Philco 41-608
John Thank you for the detailed response. I checked my connection again based on the schematic and your suggestions....tmurphy — 08:42 PM
Philco 38-2 Low Volume
Hi MrFixr55, The aux sound was good and yes it can be made too loud. The tone has no real effect on volume just tone, ge...dconant — 06:04 PM
RF Choke and Condenser -42-PT-7
Hi Folks, If you are talking about Part #7, this is the cap that capacitively grounds the physical chassis to B- and...MrFixr55 — 06:04 PM
Photo-finish repair
Thanks for the reply Bob.  I think I will try the touchup process.  Do you have any suggestions on what I should use to ...georgetownjohn — 05:52 PM
Philco 38-2 Low Volume
Hi DConant, I don't think that the extra 0.7 MOhm would make much difference. If the pot was supposed to be a 500KOhm...MrFixr55 — 05:21 PM
Photo-finish repair
Welcome to the Phorum! :wave: Once upon a time there was a supplier for some photofinish decals but no longer that I...klondike98 — 05:21 PM
Philco 38-2 Low Volume
Hi MrFixr55, Thank you for the drawing. I can handle that. I disconnected the muting switch from the center pin of the p...dconant — 04:50 PM
Philco 38-2 Low Volume
Sorry, I did not see your post as I was writing mine. I would think that with a consumer electronics level Aux input of...MrFixr55 — 04:24 PM
Philco 38-2 Low Volume
HI DConat, It wouldn't hurt to put a 0.01 uF cap between the deck and volume control.  However, there is a 0.01uF cap b...MrFixr55 — 02:57 PM

[-]
Who's Online
There are currently 1565 online users. [Complete List]
» 2 Member(s) | 1563 Guest(s)
AvatarAvatar

>