Model 96 cabinet veneer

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Model 96 cabinet veneer

TGLager
Junior Member

Posts: 6
Threads: 2
Joined: Oct 2024
City: Jim Thorpe State, Province, Country: PA

11-10-2024, 02:40 PM

I can't figure out what the first step is, let alone the final step. I have tried copying pictures from my hard drive and then pasting them into my forum post, but nothing happens.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Model 96 cabinet veneer - by TGLager - 10-23-2024, 04:48 PM

RE: Model 96 cabinet veneer - by Arran - 10-23-2024, 11:08 PM

RE: Model 96 cabinet veneer - by klondike98 - 11-04-2024, 12:59 AM

RE: Model 96 cabinet veneer - by TGLager - 11-09-2024, 04:08 PM

RE: Model 96 cabinet veneer - by RodB - 11-10-2024, 10:36 AM

RE: Model 96 cabinet veneer - by TGLager - 11-10-2024, 02:40 PM

RE: Model 96 cabinet veneer - by RodB - 11-10-2024, 07:01 PM

RE: Model 96 cabinet veneer - by TGLager - 11-10-2024, 11:02 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
[split] Newbie questions RE: Philco 41-608
I agree with Morzh. I've split this issue to it's own thread. Take care and BE HEALTHY! GaryGarySP — 09:03 PM
Newbie questions RE: Philco 41-608
John Thank you for the detailed response. I checked my connection again based on the schematic and your suggestions....tmurphy — 08:42 PM
Philco 38-2 Low Volume
Hi MrFixr55, The aux sound was good and yes it can be made too loud. The tone has no real effect on volume just tone, ge...dconant — 06:04 PM
RF Choke and Condenser -42-PT-7
Hi Folks, If you are talking about Part #7, this is the cap that capacitively grounds the physical chassis to B- and...MrFixr55 — 06:04 PM
Photo-finish repair
Thanks for the reply Bob. I think I will try the touchup process. Do you have any suggestions on what I should use to ...georgetownjohn — 05:52 PM
Philco 38-2 Low Volume
Hi DConant, I don't think that the extra 0.7 MOhm would make much difference. If the pot was supposed to be a 500KOhm...MrFixr55 — 05:21 PM
Photo-finish repair
Welcome to the Phorum! :wave: Once upon a time there was a supplier for some photofinish decals but no longer that I...klondike98 — 05:21 PM
Philco 38-2 Low Volume
Hi MrFixr55, Thank you for the drawing. I can handle that. I disconnected the muting switch from the center pin of the p...dconant — 04:50 PM
Philco 38-2 Low Volume
Sorry, I did not see your post as I was writing mine. I would think that with a consumer electronics level Aux input of...MrFixr55 — 04:24 PM
Philco 38-2 Low Volume
HI DConat, It wouldn't hurt to put a 0.01 uF cap between the deck and volume control. However, there is a 0.01uF cap b...MrFixr55 — 02:57 PM

Who's Online

There are currently 1094 online users. [Complete List]
» 5 Member(s) | 1089 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me